Print Report | Back to Sample Detail

Sample Record for 2021-04-05-29

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214764 DEA: 032H6404 EFIS: 0317000167 QA Service Level: 1
DIST-CO-RTE-PM: 03-SAC-12,160-0.4/0.9,L10.5/R0.2
Work Description: MODIFY SIGNAL AND LIGHTING SYSTEM, PLACE RHMA AND ROADWAY EXCAVATION.
Location Description: SACRAMENTO COUNTY NEAR RIO VISTA ON ROUTE 12 FROM 0.6 MILE EAST OF SACRAMENTO RIVER BRIDGE TO 5.2 MILES WEST OF MOKELUMNE RIVER BRIDGE AND ON ROUTE 160 FROM 3.6 MILES NORTH OF THREE MILE SLOUGH BRIDGE TO 2.7 MILES SOUTH OF CIRCLE DRIVE
Contractor Name: OC JONES & CO.
Contractor Address: 1520 4th Street, Berkeley, Ca 94710
Resident Engineer: Frank Cannizzaro Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2021-04-05-29
TL Number from the TL Form: C123456
Sample Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Sample Organization Contact: (530) 741-4238
Type of Sample: Verification
Type of Material: Hot Mix Asphalt
Sample Taken Date: 04/05/2021
Date that the sample was received by the laboratory/organization performing the testing: 04/06/2021
The quantity of what the sample constitutes: JMF Verification
A brief description of the sample: 3/4" RHMA-G.
From where was the sample collected: Manufacturer
Laboratory sample identification: JMF21-011
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: George Reed Inc- Clements Batch Plant

Material Information

HMA Type: RHMA-G
HMA Grading: 3/4 inch
Lot number:
Sublot number:
HMA Mix Number:

Test Results

Test 1 of 8

DIME Test ID: 2021-04-05-29-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
This test has been superseded on 05/12/2021.
Reason: retested

Test 2 of 8

DIME Test ID: 2021-04-05-29-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 05/11/2021
Date Tested: 04/28/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF21-011.
Test Result Compliance: not applicable
Additional Comments When Verified: JMF21-011
Bulk Specific Gravity 2.449
Bulk Specific Gravity 2 2.444
Bulk Specific Gravity 3 2.445
Average Bulk Specific Gravity 2.446

Test 3 of 8

DIME Test ID: 2021-04-05-29-4
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
This test has been superseded on 05/12/2021.
Reason: retested

Test 4 of 8

DIME Test ID: 2021-04-05-29-5
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 05/12/2021
Date Tested: 04/29/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF21-011.
Test Result Compliance: complies
Additional Comments When Verified: JMF21-011
Unit system used? SI Units
Average Dry Tensile Strength 159 psi
Average Wet Tensile Strength 130 psi
Tensile Strength Ratio 0.82

Test 5 of 8

DIME Test ID: 2021-04-05-29-6
Test Method: AASHTO T324-14: Standard Method of Test for Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures (Hamburg Wheel Track)
Verified Date: 05/12/2021
Date Tested: 04/29/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF21-011.
Test Result Compliance: complies
Additional Comments When Verified: JMF21-011
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel A) 20000
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel B) 20000
Impression at specified number of passes, or specified maximum impression if applicable (Wheel A) 3.62 mm
Impression at specified number of passes, or specified maximum impression if applicable (Wheel B) 3.73 mm
Stripping Inflection Point (Wheel A) 25000
Stripping Inflection Point (Wheel B) 25000

Test 6 of 8

DIME Test ID: 2021-04-05-29-7
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 05/11/2021
Date Tested: 04/27/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF21-011.
Test Result Compliance: not applicable
Additional Comments When Verified: JMF21-011
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed no data
Mass of container filled with water 7346.4 grams
Mass of oven-dry sample in air for Sample 1 2238.4 grams
Mass of container filled with the sample and water for Sample 1 8698.4 grams
Temperature of Water 76 °F
Specific Gravity for Sample 1 2.525
Theoretical maximum density at 25°C (77°F) no data

Test 7 of 8

DIME Test ID: 2021-04-05-29-8
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 05/12/2021
Date Tested: 04/27/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF21-011.
Test Result Compliance: complies
Additional Comments When Verified: JMF21-011. Test Superseded to correct the testers name
What temperature unit is used? Fahrenheit
Test procedure used? no data
Mass of HMA Sample prior to ignition no data
Corrected Asphalt Binder Content 7.40 %
Mass Loss no data
Correction Factor (Percent by mass of HMA Specimen) no data
Moisture Content no data
Temperature Compensation Factor no data
Test Temperature no data

Test 8 of 8

DIME Test ID: 2021-04-05-29-9
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 05/12/2021
Date Tested: 04/28/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF21-011.
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 3.0 %
Percent Air Voids 2 3.2
Percent Air Voids 3 3.2
Percent Air Voids Average 3.1