Print Report | Back to Test Summary

Testing Report for 2021-04-22-10-7

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

DEA: 032G1604
EFIS: 0320000235
Project ID: 215405
QA Service Level: 1
DIST-CO-RTE-PM: 03-YOL-45-0.6/12.9
Work Description: COLD PLANE AC PAVEMENT AND REPLACE WITH HOT MIX ASPHALT.
Location Description: YOLO COUNTY NEAR KNIGHTS LANDING FROM SYCAMORE SLOUGH BRIDGE TO YOLO COUNTY LINE ROAD
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Luis Pompa
Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2021-04-22-10
TL Number from the TL Form: 783792
Sample Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Sample Organization Contact: (916) 227-7302
Type of Sample: Acceptance
Type of Material: Asphalt Binder
Sample Taken Date: 4/22/2021
Date that the sample was received by the laboratory/organization performing the testing: 4/26/2021
The quantity of what the sample constitutes: 1 of 1 can
A brief description of the sample: Binder
From where was the sample collected: Manufacturer
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Teichert Hollwood

Material Information

Performance Grade: PG 64-16
Modified: No
Lot number: 1
Sublot number: 15
Tank number:
Time of sample:
HMA Supplier: Teichert Hollwood
Asphalt Binder Supplier: Marathon Petroleum Co. LP - Elk Grove CA
Multigrade: No
Multigrade Type:

Test Information

DIME Test ID: 2021-04-22-10-7
Test Method: AASHTO T313-19: Standard Method of Test for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR)
Date Tested: 4/29/2021
Verified Date: 4/29/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: PER 2018 STANDARD SPECS
Test Result Compliance: complies
Additional Comments When Verified :

Submitted Test Results

Minimum test bath temperature at 240 s: -6.0 C
Maximum test bath temperature at 240 s: -5.9 C
Time of test load application: no data
File name of test data: no data
Time beam in bath: no data
Time test started: no data
Flags issued by software during test: no data
Correlation coefficient (R²): no data
Regression coefficient a: no data
Regression coefficient b: no data
Regression coefficient c: no data
Load at time 0.0: 0.0 mN
Deflection at time 0.0 s: 0.000 µm
Load at time 0.5 s: 0.0 mN
Deflection at time 0.5 s: 0.000 µm
Load at 60.0 s: 989.0 mN
Beam deflection 60.0 s: 1.087 µm
Measured Stiffness Modulus 60.0 s: 73.400 mPa
Estimated Stiffness Modulus 60.0 s: 73.400 mPa
Difference between stiffness moduli 60.0 s: 2.08 %
Estimated m-value 60.0 s: 0.436