Print Report | Back to Sample Detail

Sample Record for 2021-03-04-27

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 213700 DEA: 020H9004 EFIS: 0215000077 QA Service Level: 1
DIST-CO-RTE-PM: 02-BUT-70-41.9/42.3
Work Description: REMOVE CULVERTS AND CONSTRUCT BRIDGE
Location Description: BUTTE COUNTY NEAR PULGA FROM 2.5 MILES WEST OF PENSTOCK UNDERCROSSING TO 2.1 MILES WEST OF PENSTOCK UNDERCROSSING
Contractor Name: SHASTA SERVICES INC. DBA
Contractor Address: 509 S. Mt. Shasta Blvd., Mt. Shasta, CA 96067
Resident Engineer: John Yolton Structure Rep.: Adam Scardaci

Sample Information

DIME Sample ID: 2021-03-04-27
TL Number from the TL Form: 896989
Sample Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Sample Organization Contact: (530) 225-3194
Type of Sample: Acceptance
Type of Material: Reclaimed Asphalt Pavement
Sample Taken Date: 03/04/2021
Date that the sample was received by the laboratory/organization performing the testing: 03/05/2021
The quantity of what the sample constitutes: Production Start-Up Evaluation
A brief description of the sample: 1/2-inch RAP (Combined)
From where was the sample collected: Manufacturer
Laboratory sample identification: D78752B
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Knife River Construction - Orland Plant

Material Information

RAP Source: Orland Plant
Aggregate Size: 1/2-inch
Aggregate Source:
RAP Stockpile:
Stockpile Size (tons):
Reclaimed Asphalt Pavement Mix Number:
Test results on following page(s): 3

Test Results

Test 1 of 3

DIME Test ID: 2021-03-04-27-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 04/22/2021
Date Tested: 03/11/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly no data
Mass of the specimen and specimen basket assembly prior to ignition no data
Mass of HMA Sample prior to ignition 1600.2 g
Corrected Asphalt Binder Content 5.24 %
Mass Loss no data
Mass of aggregate remaining after ignition 1515.8 g
Correction Factor (Percent by mass of HMA Specimen) 0.00 %
Moisture Content 0.03 %
Temperature Compensation Factor no data
Test Temperature 1000 F

Test 2 of 3

DIME Test ID: 2021-03-04-27-2
Test Method: AASHTO T30-19: Standard Method of Test for Mechanical Analysis of Extracted Aggregate (Mechanical Analysis)
Verified Date: 04/22/2021
Date Tested: 03/11/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Is an aggregate correction factor used? No
Cumulative percent passing the 2 in. sieve 100 %
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 100 %
Cumulative percent passing the 1/2 in. sieve 96.7 %
Cumulative percent passing the 3/8 in. sieve 89.3 %
Cumulative percent passing the 1/4 in. sieve 72.3 %
Cumulative percent passing the #4 sieve 58.3 %
Cumulative percent passing the #8 sieve 39.1 %
Cumulative percent passing the #16 sieve 28.3 %
Cumulative percent passing the #30 sieve 20.9 %
Cumulative percent passing the #50 sieve 14.6 %
Cumulative percent passing the #100 sieve 10.3 %
Cumulative percent passing the #200 sieve 7.9 %

Test 3 of 3

DIME Test ID: 2021-03-04-27-3
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 04/22/2021
Date Tested: 03/09/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7336.6 grams
Mass of oven-dry sample in air for Sample 1 1594.2 grams
Mass of container filled with the sample and water for Sample 1 8315.7 grams
Temperature of Water 76 °F
Specific Gravity for Sample 1 2.592
Theoretical maximum density at 25°C (77°F) no data