Print Report | Back to Sample Detail

Sample Record for 2020-06-19-23

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214841 DEA: 034H1004 EFIS: 0318000176 QA Service Level: 1
DIST-CO-RTE-PM: 03-SIE-49-9.2/24.7
Work Description: INSTALL RETAINING STRUCTURE AND RSP CONCRETE EMBANKMENT.
Location Description: SIERRA COUNTY ON ROUTE 49 AT VARIOUS LOCATIONS
Contractor Name: GORDON N BALL INC
Contractor Address: 333 CAMILLE AVENUE, ALAMO CA 94507
Resident Engineer: Christopher Fallbeck Structure Rep.: Jimmer Ross

Sample Information

DIME Sample ID: 2020-06-19-23
TL Number from the TL Form: c777828
Sample Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Sample Organization Contact: (530) 741-4238
Type of Sample: Verification
Type of Material: Aggregate
Sample Taken Date: 06/19/2020
Date that the sample was received by the laboratory/organization performing the testing: 06/22/2020
The quantity of what the sample constitutes: JMF Verification
A brief description of the sample: 3/4" HMA - A
From where was the sample collected: Manufacturer
Laboratory sample identification: JMF20-026
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Vulcan Materials GVA

Material Information

Source Identification (SMARA, name of Pit or Job Site): 91-29-0006
The fabricator's/manufacturer's product name for the sample:
The fabricator/manufacturer designation for the sample:
The plant number:
A detailed description of where the material sample was collected: Hot Bins
Where the material sample would have been placed if not sampled:
Primary Aggregate Nominal Size: 3/4 inch
The concrete mix design number:
Lot number:
Sublot number:
Aggregate Mix Number:
Test results on following page(s): 9

Test Results

Test 1 of 9

DIME Test ID: 2020-06-19-23-1
Test Method: AASHTO T335-09r13: Standard Method of Test for Determining the Percentage of Fracture in Coarse Aggregate (Percent of Crushed Particles)
Verified Date: 02/08/2021
Date Tested: 07/02/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-026. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-026
Method 2 - Individual Fracture Determination
Aggregate Size and Fracture Type Coarse 1 and 2 Faced and Fine 1 Faced
Weighted average percentage of fractured, coarse, 2 faced particles 92 %
Weighted average percentage of fractured, coarse, 1 faced particles 96 %
Percentage of fractured, fine, 1 faced particles tested 98 %

Test 2 of 9

DIME Test ID: 2020-06-19-23-2
Test Method: AASHTO T96-02r10: Standard Method of Test for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine (Los Angeles Rattler)
Verified Date: 02/08/2021
Date Tested: 07/02/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-026. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-026
Grading designation C
Percent loss after 100 revolutions 8 %
Percent loss after 500 revolutions 34 %

Test 3 of 9

DIME Test ID: 2020-06-19-23-3
Test Method: AASHTO T176-08: Standard Method of Test for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test (Sand Equivalent)
Verified Date: 02/08/2021
Date Tested: 06/24/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-026. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-026
Sand Equivalent 74

Test 4 of 9

DIME Test ID: 2020-06-19-23-4
Test Method: AASHTO T304-11: Standard Method of Test for Uncompacted Void Content of Fine Aggregate (Fine of Crushed Particles)
Verified Date: 02/08/2021
Date Tested: 07/01/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-026. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-026
What test method is performed? Method A
Bulk dry specific gravity 2.652
Average uncompacted voids 47.1 %

Test 5 of 9

DIME Test ID: 2020-06-19-23-5
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Verified Date: 02/08/2021
Date Tested: 06/30/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-026. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-026
Method B
Determination By Mass
Dimensional ratio used 5:1
Weighted percentage of particles (by mass) that were flat and elongated 1 %
Weighted percentage of particles (by mass) that were not flat and elongated 99 %

Test 6 of 9

DIME Test ID: 2020-06-19-23-6
Test Method: CTM 204-June 2010: Method of Test for Liquid Limit, Plastic Limit and Plasticity Index of Soils (Plasticity Index)
Verified Date: 02/08/2021
Date Tested: 06/29/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-026. Test date only for DIME entry.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-026
Plastic Index(PI) NP
Liquid Limit (LL) 0 %
Plastic Limit (PL) 0 %

Test 7 of 9

DIME Test ID: 2020-06-19-23-7
Test Method: AASHTO T85-13: Standard Method of Test for Specific Gravity and Absorption of Coarse Aggregate (Coarse Specific Gravity)
Verified Date: 02/08/2021
Date Tested: 06/26/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-026. Test date estimated.
Test Result Compliance: not applicable
Additional Comments When Verified: JMF20-026
Basis for relative density testing Bulk
Specific Gravity 2.643
Absorption 0.9 %

Test 8 of 9

DIME Test ID: 2020-06-19-23-8
Test Method: AASHTO T84-14: Standard Method of Test for Specific Gravity and Absorption of Fine Aggregate (Fine Specific Gravity)
Verified Date: 02/08/2021
Date Tested: 06/25/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-026. Test date estimated.
Test Result Compliance: not applicable
Additional Comments When Verified: JMF20-026
Bulk specific gravity 2.652
Bulk specific gravity (SSD Basis) 2.678
Apparent specific gravity 2.723
Absorption 1 %

Test 9 of 9

DIME Test ID: 2020-06-19-23-9
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 02/08/2021
Date Tested: 06/23/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-026. Test date estimated. Thomas
Test Result Compliance: complies
Additional Comments When Verified: JMF20-026
What type of gradation is being tested? HMA Gradation
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 99 %
Cumulative percent passing the 1/2 in. sieve 86 %
Cumulative percent passing the 3/8 in. sieve 73 %
Cumulative percent passing the #4 sieve 48 %
Cumulative percent passing the #8 sieve 33 %
Cumulative percent passing the #16 sieve 22 %
Cumulative percent passing the #30 sieve 14 %
Cumulative percent passing the #50 sieve 9 %
Cumulative percent passing the #100 sieve 6 %
Cumulative percent passing the #200 sieve 3.3 %