Print Report | Back to Sample Detail

Sample Record for 2020-04-15-41

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214642 DEA: 031G6704 EFIS: 0319000117 QA Service Level: 1
DIST-CO-RTE-PM: 03---
Work Description: COLD PLANE AC PAVEMENT AND RHMA-G OVERLAY.
Location Description: GLENN COUNTY NEAR WILLOWS FROM 2.3 MILES EAST OF NYE CREEK BRIDGE TO 0.2 MILE WEST OF ROUTE 162/5 SEPARATION
Contractor Name: BALDWIN CONTRACTING CO., INC. DBA KNIFE RIVER CONSTRUCTION
Contractor Address: 1764 Skyway, CHICO, CA 95928
Resident Engineer: Daniel Rechs Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2020-04-15-41
TL Number from the TL Form: C779099
Sample Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Sample Organization Contact: (530) 741-4238
Type of Sample: Verification
Type of Material: Aggregate
Sample Taken Date: 04/15/2020
Date that the sample was received by the laboratory/organization performing the testing: 04/16/2020
The quantity of what the sample constitutes: JMF Verification
A brief description of the sample: 3/4" RHMA-G
From where was the sample collected: Manufacturer
Laboratory sample identification: JMF20-016
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: KRC Orland Drum Plant

Material Information

Source Identification (SMARA, name of Pit or Job Site): 91-11-0007
The fabricator's/manufacturer's product name for the sample:
The fabricator/manufacturer designation for the sample:
The plant number:
A detailed description of where the material sample was collected: Cold Feed
Where the material sample would have been placed if not sampled:
Primary Aggregate Nominal Size: 3/4 inch
The concrete mix design number:
Lot number:
Sublot number:
Aggregate Mix Number:

Test Results

Test 1 of 10

DIME Test ID: 2020-04-15-41-1
Test Method: AASHTO T335-09r13: Standard Method of Test for Determining the Percentage of Fracture in Coarse Aggregate (Percent of Crushed Particles)
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
This test has been superseded on 01/19/2021.
Reason: corrected

Test 2 of 10

DIME Test ID: 2020-04-15-41-2
Test Method: AASHTO T96-02r10: Standard Method of Test for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine (Los Angeles Rattler)
Verified Date: 01/11/2021
Date Tested: 04/29/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-016. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified:
Grading designation C
Percent loss after 100 revolutions 3 %
Percent loss after 500 revolutions 19 %

Test 3 of 10

DIME Test ID: 2020-04-15-41-3
Test Method: AASHTO T176-08: Standard Method of Test for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test (Sand Equivalent)
Verified Date: 01/11/2021
Date Tested: 04/20/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-016. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified:
Sand Equivalent 72

Test 4 of 10

DIME Test ID: 2020-04-15-41-4
Test Method: AASHTO T304-11: Standard Method of Test for Uncompacted Void Content of Fine Aggregate (Fine of Crushed Particles)
Verified Date: 01/11/2021
Date Tested: 04/27/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-016. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified:
What test method is performed? Method A
Bulk dry specific gravity 2.622
Average uncompacted voids 46.1 %

Test 5 of 10

DIME Test ID: 2020-04-15-41-5
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Verified Date: 01/11/2021
Date Tested: 04/24/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-016. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified:
Method B
Determination By Mass
Dimensional ratio used 5:1
Weighted percentage of particles (by mass) that were flat and elongated 1 %
Weighted percentage of particles (by mass) that were not flat and elongated 99 %

Test 6 of 10

DIME Test ID: 2020-04-15-41-6
Test Method: CTM 204-June 2010: Method of Test for Liquid Limit, Plastic Limit and Plasticity Index of Soils (Plasticity Index)
Verified Date: 01/11/2021
Date Tested: 04/23/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-016
Test Result Compliance: complies
Additional Comments When Verified:
Plastic Index(PI) NP
Liquid Limit (LL) 0 %
Plastic Limit (PL) 0 %

Test 7 of 10

DIME Test ID: 2020-04-15-41-7
Test Method: AASHTO T85-13: Standard Method of Test for Specific Gravity and Absorption of Coarse Aggregate (Coarse Specific Gravity)
Verified Date: 01/11/2021
Date Tested: 04/22/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-016. Test date estimated.
Test Result Compliance: not applicable
Additional Comments When Verified:
Basis for relative density testing Bulk
Specific Gravity 2.742
Absorption 1 %

Test 8 of 10

DIME Test ID: 2020-04-15-41-8
Test Method: AASHTO T84-14: Standard Method of Test for Specific Gravity and Absorption of Fine Aggregate (Fine Specific Gravity)
Verified Date: 01/11/2021
Date Tested: 04/21/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-016. Test date estimated.
Test Result Compliance: not applicable
Additional Comments When Verified:
Bulk specific gravity 2.622
Bulk specific gravity (SSD Basis) 2.670
Apparent specific gravity 2.753
Absorption 1.8 %

Test 9 of 10

DIME Test ID: 2020-04-15-41-9
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 01/11/2021
Date Tested: 04/16/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-016. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified:
What type of gradation is being tested? HMA Gradation
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 98 %
Cumulative percent passing the 1/2 in. sieve 82 %
Cumulative percent passing the 3/8 in. sieve 61 %
Cumulative percent passing the #4 sieve 36 %
Cumulative percent passing the #8 sieve 21 %
Cumulative percent passing the #16 sieve 13 %
Cumulative percent passing the #30 sieve 9 %
Cumulative percent passing the #50 sieve 6 %
Cumulative percent passing the #100 sieve 4 %
Cumulative percent passing the #200 sieve 2.2 %

Test 10 of 10

DIME Test ID: 2020-04-15-41-10
Test Method: AASHTO T335-09r13: Standard Method of Test for Determining the Percentage of Fracture in Coarse Aggregate (Percent of Crushed Particles)
Verified Date: 01/19/2021
Date Tested: 04/28/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-016. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified:
Method 1 - Combined Fracture Determination
Aggregate Size and Fracture Type Coarse 1 and 2 Faced and Fine 1 Faced
Percentage of fractured, coarse, 2 faced particles tested 90 %
Percentage of fractured, coarse, 1 faced particles tested 96 %
Percentage of fractured, fine, 1 faced particles tested 92 %