Print Report | Back to Sample Detail

Sample Record for 2023-08-25-13

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 993647 DEA: 081K0504 EFIS: 0818000173 QA Service Level: 1
DIST-CO-RTE-PM: 08-RIV,SBD-62-84.9/90.2,90.2/94.0
Work Description: RHMA-G, PARTIAL DEPTH RECYCLING AND RECYCLING AGENT.
Location Description: RIVERSIDE AND SAN BERNADINO COUNTIES NEAR VIDAL JUNCTION FROM ROUTE 177 TO 1.7 MILES EAST OF IRON MOUNTAIN PUMPING PLANT ROAD
Contractor Name: CALMEX ENGINEERING, INC.
Contractor Address: 2750 S. LILAC AVE, BLOOMINGTON CA 92316
Resident Engineer: Francisco Montellano Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2023-08-25-13
TL Number from the TL Form:
Sample Submitted By Organization: CT D08 - Fontana Southern Regional Laboratory
Sample Organization Contact: 213-792-4794
Type of Sample: Department Acceptance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 08/25/2023
Date that the sample was received by the laboratory/organization performing the testing: 08/17/2023
The quantity of what the sample constitutes: 40 BOXES OF HMA
A brief description of the sample: 1/2" RHMA-G 0.3% EVO
From where was the sample collected: Manufacturer
Laboratory sample identification: 0419G-23
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Martin-Murrieta Coachella

Material Information

HMA Type: RHMA-G
HMA Grading: 1/2 inch
Lot number:
Sublot number:
HMA Mix Number: 41218080
Test results on following page(s): 4

Test Results

Test 1 of 4

DIME Test ID: 2023-08-25-13-1
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 09/08/2023
Date Tested: 08/18/2023
Submitted By Organization: CT D08 - Fontana Southern Regional Laboratory
Organization Address: 13970 Victoria Street,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 9098293029
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? SI Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7352.8 grams
Mass of oven-dry sample in air for Sample 1 1555.4 grams
Mass of container filled with the sample and water for Sample 1 8261.1 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.404
Theoretical maximum density at 25°C (77°F) 2397.0 kg/m^3

Test 2 of 4

DIME Test ID: 2023-08-25-13-2
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 09/08/2023
Date Tested: 08/24/2023
Submitted By Organization: CT D08 - Fontana Southern Regional Laboratory
Organization Address: 13970 Victoria Street,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 9098293029
General Comments for this Test:
Test Result Compliance: does not comply
Additional Comments When Verified:
Percent Air Voids 6.5 %
Percent Air Voids 2 6.4 %
Percent Air Voids 3 6.9 %
Percent Air Voids Average 6.6 %

Test 3 of 4

DIME Test ID: 2023-08-25-13-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 09/08/2023
Date Tested: 08/24/2023
Submitted By Organization: CT D08 - Fontana Southern Regional Laboratory
Organization Address: 13970 Victoria Street,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 9098293029
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Bulk Specific Gravity 2.248
Bulk Specific Gravity 2 2.251
Bulk Specific Gravity 3 2.238
Average Bulk Specific Gravity 2.246

Test 4 of 4

DIME Test ID: 2023-08-25-13-4
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 09/08/2023
Date Tested: 08/18/2023
Submitted By Organization: CT D08 - Fontana Southern Regional Laboratory
Organization Address: 13970 Victoria Street,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 9098293029
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of HMA Sample prior to ignition 1623.9 g
Corrected Asphalt Binder Content 7.17 %
Mass Loss 117.3 g
Correction Factor (Percent by mass of HMA Specimen) -0.08 %
Moisture Content 0.00 %
Temperature Compensation Factor 0.00 %
Test Temperature 738 C