Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project ID: 993208 DEA: 034F38U4 EFIS: 0321000092
QA Service Level: 1
DIST-CO-RTE-PM: 03-YUB-70-16.2/25.8
Work Description: WIDEN SHOULDERS AND IMPROVE CLEAR RECOVERY ZONE.
Location Description: YUBA COUNTY NEAR MARYSVILLE FROM 0.2 MILE NORTH OF LAURELLEN ROAD TO SOUTH HONCUT CREEK BRIDGE
Contractor Name: DeSilva Gates
Contractor Address: 11555 Dublin Boulevard, Dublin, CA 94568
Resident Engineer: Manoharan Selvendran Structure Rep.: Unknown
DIME Sample ID: 2023-06-16-47
TL Number from the TL Form: 778756
Sample Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Sample Organization Contact: (530) 741-4238
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 06/16/2023
Date that the sample was received by the laboratory/organization performing the testing: 06/16/2023
The quantity of what the sample constitutes: 750 Tons
A brief description of the sample: 3/4 HMA
From where was the sample collected: Source
Laboratory sample identification: 23-067
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Desilva Gates-Marysville
DIME Test ID: 2023-06-16-47-1
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 06/27/2023
Date Tested: 06/19/2023
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
What is the unit of measurement for theoretical density?
|
SI Units
|
Mass Determination
|
Air
|
Method Performed
|
Mechanical Agitation - Method A
|
Mass of container filled with water 1
|
7345.5 grams
|
Mass of oven-dry sample in air for Sample 1
|
2652.3 grams
|
Mass of container filled with the sample and water for Sample 1
|
8961.0 grams
|
Temperature of Water
|
77 °F
|
Specific Gravity for Sample 1
|
2.558
|
Theoretical maximum density at 25°C (77°F)
|
2550.6 kg/m^3
|
DIME Test ID: 2023-06-16-47-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 06/27/2023
Date Tested: 06/19/2023
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used?
|
Celsius
|
Test procedure used?
|
Method A
|
Mass of the specimen basket assembly
|
4000.0 g
|
Mass of the specimen and specimen basket assembly prior to ignition
|
6091.5 g
|
Mass of HMA Sample prior to ignition
|
2091.5 g
|
Corrected Asphalt Binder Content
|
5.01 %
|
Mass Loss
|
115.4 g
|
Mass of aggregate remaining after ignition
|
1976.1 g
|
Correction Factor (Percent by mass of HMA Specimen)
|
0.51 %
|
Moisture Content
|
0.00 %
|
Temperature Compensation Factor
|
0.00 %
|
Test Temperature
|
538 C
|