Print Report | Back to Sample Detail

Sample Record for 2023-02-01-30

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 993124 DEA: 101F1704 EFIS: 1016000032 QA Service Level: 1
DIST-CO-RTE-PM: 10-SJ-26,99-1.1,19.3
Work Description: REMOVE AND REPLACE BRIDGE.
Location Description: SAN JOAQUIN COUNTY NEAR STOCKTON AT ROUTE 26/99 SEPARATION
Contractor Name: Andrew M Jordan Inc, DBA A & B Construction
Contractor Address: 1350 4th Street, Berkeley, CA 94710
Resident Engineer: Troy Scheiber Structure Rep.: Chuck Pazzi

Sample Information

DIME Sample ID: 2023-02-01-30
TL Number from the TL Form: 032234
Sample Submitted By Organization: CT D10 - District 10 Materials Laboratory
Sample Organization Contact: (209) 948-7567
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 02/01/2023
Date that the sample was received by the laboratory/organization performing the testing: 02/06/2023
The quantity of what the sample constitutes: 4 boxes
A brief description of the sample: 3/4 HMA-A
From where was the sample collected: Manufacturer
Laboratory sample identification: 23-h-010
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Teichert Vernalis

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number: 2
Sublot number: 1
HMA Mix Number: 22 006
Test results on following page(s): 2

Test Results

Test 1 of 2

DIME Test ID: 2023-02-01-30-1
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 04/19/2023
Date Tested: 02/10/2023
Submitted By Organization: CT D10 - District 10 Materials Laboratory
Organization Address: 1976 East Dr. Martin Luther King Jr. Boulevard,
Organization City: Stockton
Organization State: CA
Organization Zipcode: 95205
Organization Email: mandeep.dhesi@dot.ca.gov
Organization Phone: (209) 948-7567
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Water
Specific Gravity for Sample 1 2.495
Theoretical maximum density at 25°C (77°F) 155.3 lb/ft^3

Test 2 of 2

DIME Test ID: 2023-02-01-30-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 04/19/2023
Date Tested: 02/10/2023
Submitted By Organization: CT D10 - District 10 Materials Laboratory
Organization Address: 1976 East Dr. Martin Luther King Jr. Boulevard,
Organization City: Stockton
Organization State: CA
Organization Zipcode: 95205
Organization Email: mandeep.dhesi@dot.ca.gov
Organization Phone: (209) 948-7567
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of HMA Sample prior to ignition 2204.0 g
Corrected Asphalt Binder Content 4.85 %
Mass Loss 125.8 g
Correction Factor (Percent by mass of HMA Specimen) 0.72 %
Moisture Content 0.00 %
Temperature Compensation Factor 0.14 %
Test Temperature 538 F