Sample Record for 2023-01-26-35
Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project Information
Project ID: 994358 DEA: 033J3304 EFIS: 0322000251
QA Service Level: 1
DIST-CO-RTE-PM: 03-SAC/SAC-12-0/0.5
Work Description: Replace backup drive system, replace lift span deck, install hydraulic barrier system and new generator, replace electrical control system, install new traffic gates and elevators, traffic control,
Location Description:
Contractor Name: Golden State Bridge, Inc.
Contractor Address: 3701 Mallard Drive, Benicia, CA 94510
Resident Engineer: Masoud Saed Structure Rep.: Rusty D'Anna
Sample Information
DIME Sample ID: 2023-01-26-35
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - Sacramento Aggregate Testing Laboratory
Sample Organization Contact: (916) 227-7204
Type of Sample: Per Request
Type of Material: Aggregate
Sample Taken Date: 01/26/2023
Date that the sample was received by the laboratory/organization performing the testing: 01/27/2023
The quantity of what the sample constitutes: 1-5 gallon bucket
A brief description of the sample: lightweight Sand
From where was the sample collected: Source
Laboratory sample identification: 23-LWF-0007
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: na
Material Information
Source Identification (SMARA, name of Pit or Job Site): 0000
The fabricator's/manufacturer's product name for the sample:
The fabricator/manufacturer designation for the sample:
The plant number:
A detailed description of where the material sample was collected: Volumetric Truck
Where the material sample would have been placed if not sampled:
Primary Aggregate Nominal Size: fine
The concrete mix design number:
Lot number:
Sublot number:
Aggregate Mix Number:
Test Results
Test 1 of 4
DIME Test ID: 2023-01-26-35-1
Test Method: ASTM C566-13: Standard Test Method for Total Evaporable Moisture Content of Aggregate by Drying
Verified Date: 02/01/2023
Date Tested: 02/01/2023
Submitted By Organization: CT HQ - Sacramento Aggregate Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: bang.d.nguyen@dot.ca.gov
Organization Phone: (916) 227-7204
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Total evaporable moisture content
|
18.2 %
|
Test 2 of 4
DIME Test ID: 2023-01-26-35-2
Test Method: ASTM C136-19: Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
Verified Date: 02/01/2023
Date Tested: 02/01/2023
Submitted By Organization: CT HQ - Sacramento Aggregate Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: bang.d.nguyen@dot.ca.gov
Organization Phone: (916) 227-7204
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
What type of gradation is being tested?
|
Fine Aggregate
|
Cumulative percent passing the 3/8 in. sieve
|
100 %
|
Cumulative percent passing the #4 sieve
|
100 %
|
Cumulative percent passing the #8 sieve
|
89 %
|
Cumulative percent passing the #16 sieve
|
47 %
|
Cumulative percent passing the #30 sieve
|
21 %
|
Cumulative percent passing the #50 sieve
|
9 %
|
Cumulative percent passing the #100 sieve
|
5 %
|
Cumulative percent passing the #200 sieve
|
2.4 %
|
Test 3 of 4
DIME Test ID: 2023-01-26-35-3
Test Method: ASTM C128-12: Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate
Verified Date: 02/03/2023
Date Tested: 02/03/2023
Submitted By Organization: CT HQ - Sacramento Aggregate Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: bang.d.nguyen@dot.ca.gov
Organization Phone: (916) 227-7204
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Basis for testing
|
Oven Dry
|
Specific Gravity
|
1.64
|
Density
|
1640 kg/m^3
|
Absorption
|
13.67 %
|
Test 4 of 4
DIME Test ID: 2023-01-26-35-4
Test Method: ASTM C128-12: Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate
Verified Date: 02/03/2023
Date Tested: 02/03/2023
Submitted By Organization: CT HQ - Sacramento Aggregate Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: bang.d.nguyen@dot.ca.gov
Organization Phone: (916) 227-7204
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Basis for testing
|
Saturated Surface Dry
|
Specific Gravity
|
1.87
|
Density
|
1860 kg/m^3
|
Absorption
|
13.67 %
|