Print Report | Back to Sample Detail

Sample Record for 2022-11-08-4

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 88887 DEA: PC-Barrier-STOCK EFIS: PC-Barrier-STOCK QA Service Level:
DIST-CO-RTE-PM: 59---
Work Description: Special project for precast barrier rail stock material.
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2022-11-08-4
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - QASI Los Angeles Field Office
Sample Organization Contact: (858) 285-5797
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 11/08/2022
Date that the sample was received by the laboratory/organization performing the testing: 11/09/2022
The quantity of what the sample constitutes: 350
A brief description of the sample: ASTM A449 All Thread Rod
From where was the sample collected: Fabricator
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: UIS Lindon UT

Material Information

Rocap Number(s): NA
Heat Number(s): DL20100222
Nut Mfg. Lot Number(s): NA
Washer Mfg. Lot Number(s): NA
Bolt Specification: ASTM A449
Bolt Length(s): 12"
Nut Specification: NA
Washer Specification: NA
Finish: Hot Dip
Diameter/Size: 3/4-10 x 12
Bolt Mfg. Lot Number: 34784
Rocap Test Requirement(s): NA
Lubricant Requirements(s): NA
Test results on following page(s): 12

Test Results

Test 1 of 12

DIME Test ID: 2022-11-08-4-1
Test Method: ASTM F606-21: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A449 Tensile
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleSizeArea (in^2)Peak Load (lbf)Peak Load (kN)Tensile Strength (psi)Stress at Offset (psi)Load at Offset (lbf)Comments
1AUNC 3/4 0.3344548220213616912495241734A449 Tensile
UTM 400kip
Temperature 72

Test 2 of 12

DIME Test ID: 2022-11-08-4-2
Test Method: ASTM F606-21: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A449 Tensile
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleSizeArea (in^2)Peak Load (lbf)Peak Load (kN)Tensile Strength (psi)Stress at Offset (psi)Load at Offset (lbf)Comments
1BUNC 3/4 0.3344574420313694712527641842A449 Tensile
UTM 400kip
Temperature 72

Test 3 of 12

DIME Test ID: 2022-11-08-4-3
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) DL2100222
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .75 in
Bolt Length 12 in
Gage Type Pass

Test 4 of 12

DIME Test ID: 2022-11-08-4-4
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) DL2100222
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .75 in
Bolt Length 12 in
Gage Type Pass

Test 5 of 12

DIME Test ID: 2022-11-08-4-5
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) DL2100222
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .75 in
Bolt Length 12 in
Gage Type Pass

Test 6 of 12

DIME Test ID: 2022-11-08-4-6
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1D
Rocap Number no data
Heat Number(s) DL2100222
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .75 in
Bolt Length 12 in
Gage Type Pass

Test 7 of 12

DIME Test ID: 2022-11-08-4-7
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1E
Rocap Number no data
Heat Number(s) DL2100222
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .75 in
Bolt Length 12 in
Gage Type Pass

Test 8 of 12

DIME Test ID: 2022-11-08-4-8
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) DL2100222
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .75 in
Bolt Length 12 in
Measurement Average 2.36 mils

Test 9 of 12

DIME Test ID: 2022-11-08-4-9
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) DL2100222
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .75 in
Bolt Length 12 in
Measurement Average 2.64 mils

Test 10 of 12

DIME Test ID: 2022-11-08-4-10
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) DL2100222
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .75 in
Bolt Length 12 in
Measurement Average 3.41 mils

Test 11 of 12

DIME Test ID: 2022-11-08-4-11
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1D
Rocap Number no data
Heat Number(s) DL2100222
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .75 in
Bolt Length 12 in
Measurement Average 6.71 mils

Test 12 of 12

DIME Test ID: 2022-11-08-4-12
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/17/2022
Date Tested: 11/09/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1E
Rocap Number no data
Heat Number(s) DL2100222
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .75 in
Bolt Length 12 in
Measurement Average 2.4 mils