Print Report | Back to Sample Detail

Sample Record for 2022-08-30-80

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 993628 DEA: 081M0504 EFIS: 0821000064 QA Service Level: 1
DIST-CO-RTE-PM: 08-RIV-15,215-23.9/33.4,R8.4/41.5
Work Description: COLD PLANE AC PVMT, RHMA, AND REPLACE ASPHALT CONCRETE SURFACING.
Location Description: RIVERSIDE COUNTY ON ROUTE 15 FROM 0.1 MILE NORTH OF NICHOLS ROAD OVERCROSSING TO 0.1 MILE NORTH OF TEMESCAL CANYON ROAD UNDERCROSSING AND ON ROUTE 215 FROM 1.1 MILES SOUTH OF MURRIETA HOT SPRINGS ROAD UNDERCROSSING TO UNIVERSITY AVENUE UNDERCROSSING.
Contractor Name: ALL AMERICAN ASPHALT
Contractor Address: Unknown
Resident Engineer: BERGEVIN MICHAEL Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2022-08-30-80
TL Number from the TL Form:
Sample Submitted By Organization: CT D08 - Fontana Field Testing Laboratory
Sample Organization Contact: 9512323690
Type of Sample: Department Acceptance
Type of Material: Aggregate
Sample Taken Date: 08/30/2022
Date that the sample was received by the laboratory/organization performing the testing: 08/31/2022
The quantity of what the sample constitutes: 1 Bags Of Combined Aggregate
A brief description of the sample: 3/4" RHMA-G-SP
From where was the sample collected: Manufacturer
Laboratory sample identification: 0476G-22
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: All American Asphalt - Corona

Material Information

Source Identification (SMARA, name of Pit or Job Site): 91-33-0005
The fabricator's/manufacturer's product name for the sample:
The fabricator/manufacturer designation for the sample:
The plant number: 106835
A detailed description of where the material sample was collected: Belt Cut at All American Corona Plant
Where the material sample would have been placed if not sampled:
Primary Aggregate Nominal Size: 3/4 inch
The concrete mix design number:
Lot number:
Sublot number:
Aggregate Mix Number:
Test results on following page(s): 2

Test Results

Test 1 of 2

DIME Test ID: 2022-08-30-80-1
Test Method: AASHTO T176-08: Standard Method of Test for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test (Sand Equivalent)
Verified Date: 09/15/2022
Date Tested: 09/01/2022
Submitted By Organization: CT D08 - Fontana Field Testing Laboratory
Organization Address: 13970 Victoria Street,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: prakash.gowda@dot.ca.gov
Organization Phone: (951) 232-3690
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Sand Equivalent 76

Test 2 of 2

DIME Test ID: 2022-08-30-80-2
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 09/15/2022
Date Tested: 09/01/2022
Submitted By Organization: CT D08 - Fontana Field Testing Laboratory
Organization Address: 13970 Victoria Street,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: prakash.gowda@dot.ca.gov
Organization Phone: (951) 232-3690
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What type of gradation is being tested? Combined Gradation
Cumulative percent passing the 2 in. sieve 100 %
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 96 %
Cumulative percent passing the 1/2 in. sieve 80 %
Cumulative percent passing the 3/8 in. sieve 61 %
Cumulative percent passing the #4 sieve 32 %
Cumulative percent passing the #8 sieve 20 %
Cumulative percent passing the #16 sieve 13 %
Cumulative percent passing the #30 sieve 9 %
Cumulative percent passing the #50 sieve 6 %
Cumulative percent passing the #100 sieve 4 %
Cumulative percent passing the #200 sieve 3 %