Print Report | Back to Sample Detail

Sample Record for 2022-02-21-5

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 77777 DEA: CHEM-STOCK EFIS: CHEM-STOCK QA Service Level:
DIST-CO-RTE-PM: 59---
Work Description: Special project for Chem Lab stock material. Object Code: 1025. J2 DEA: 912680.
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2022-02-21-5
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - QASI Sacramento Field Office
Sample Organization Contact: (916) 2058871
Type of Sample: Department Acceptance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 02/21/2022
Date that the sample was received by the laboratory/organization performing the testing: 02/23/2022
The quantity of what the sample constitutes: 195 142
A brief description of the sample: 1" x 5" a325 hdg
From where was the sample collected: Distributor
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: QFC

Material Information

Rocap Number(s): 021022-2, 021022-3
Heat Number(s): 10700930
Nut Mfg. Lot Number(s): na
Washer Mfg. Lot Number(s): na
Bolt Specification: a325
Bolt Length(s): 5"
Nut Specification: na
Washer Specification: na
Finish: hdg
Diameter/Size: 1"
Bolt Mfg. Lot Number: L104U1 L913U1
Rocap Test Requirement(s): yes
Lubricant Requirements(s): yes
Test results on following page(s): 14

Test Results

Test 1 of 14

DIME Test ID: 2022-02-21-5-1
Test Method: ASTM F606-21: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 03/02/2022
Date Tested: 02/25/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A325 Wedge Tensile
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
1AL104U11.000089354397.4710.00A325 Wedge Tensilespaine
UTM 450kip
Temperature no data

Test 2 of 14

DIME Test ID: 2022-02-21-5-2
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 03/02/2022
Date Tested: 02/25/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L104U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Gage Type Pass

Test 3 of 14

DIME Test ID: 2022-02-21-5-3
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 03/02/2022
Date Tested: 02/25/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L104U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Gage Type Pass

Test 4 of 14

DIME Test ID: 2022-02-21-5-4
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 03/02/2022
Date Tested: 02/25/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L104U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Gage Type Pass

Test 5 of 14

DIME Test ID: 2022-02-21-5-5
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/02/2022
Date Tested: 02/25/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L104U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Measurement Average 2.88 mils

Test 6 of 14

DIME Test ID: 2022-02-21-5-6
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/02/2022
Date Tested: 02/25/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L104U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Measurement Average 3.14 mils

Test 7 of 14

DIME Test ID: 2022-02-21-5-7
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/02/2022
Date Tested: 02/25/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L104U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Measurement Average 3.18 mils

Test 8 of 14

DIME Test ID: 2022-02-21-5-8
Test Method: ASTM F606-21: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 03/02/2022
Date Tested: 02/28/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A325 Wedge Tensile
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
2AL913U11.000091166405.5210.00A325 Wedge Tensilespaine
UTM 450kip
Temperature no data

Test 9 of 14

DIME Test ID: 2022-02-21-5-9
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 03/02/2022
Date Tested: 02/28/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L913U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Gage Type Pass

Test 10 of 14

DIME Test ID: 2022-02-21-5-10
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 03/02/2022
Date Tested: 02/28/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L913U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Gage Type Pass

Test 11 of 14

DIME Test ID: 2022-02-21-5-11
Test Method: ASME B1.2-83r17: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 03/02/2022
Date Tested: 02/28/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L913U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Gage Type Pass

Test 12 of 14

DIME Test ID: 2022-02-21-5-12
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/02/2022
Date Tested: 02/28/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L913U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Measurement Average 3.85 mils

Test 13 of 14

DIME Test ID: 2022-02-21-5-13
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/02/2022
Date Tested: 02/28/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L913U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Measurement Average 3.77 mils

Test 14 of 14

DIME Test ID: 2022-02-21-5-14
Test Method: ASTM B499-09r21: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/02/2022
Date Tested: 02/28/2022
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number L913U1
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size 1 in
Bolt Length 5 in
Measurement Average 2.97 mils