Print Report | Back to Sample Detail

Sample Record for 2021-09-21-18

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214665 DEA: 081G5504 EFIS: 0816000035 QA Service Level: 1
DIST-CO-RTE-PM: 08-SBD-40-R28.9
Work Description: REPLACE WEIGH-IN-MOTION SYSTEM WITH HIGH SPEED WEIGH-IN-MOTION SYSTEM.
Location Description: SAN BERNARDINO COUNTY NEAR NEWBERRY SPRINGS AT 3.6 MILES WEST OF HECTOR ROAD UNDERCROSSING
Contractor Name: Global Road Sealing Inc
Contractor Address: 10832 Dorothy Ave, Garden Grove, CA, 92843
Resident Engineer: Thanh Pham Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2021-09-21-18
TL Number from the TL Form:
Sample Submitted By Organization: CT - Southern Regional Laboratory
Sample Organization Contact: 213-792-4794
Type of Sample: Verification
Type of Material: Aggregate
Sample Taken Date: 09/21/2021
Date that the sample was received by the laboratory/organization performing the testing: 09/23/2021
The quantity of what the sample constitutes: 3 Bags of Combined Aggregate, 11 Bags of Aggregate
A brief description of the sample: PSUE 1/2" RHMA-G-0.6% Evotherm
From where was the sample collected: Manufacturer
Laboratory sample identification: 0544G-21
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Blue Diamond Victorville

Material Information

Source Identification (SMARA or name of Pit): 91-36-0046,91-36-0106
The fabricator's/manufacturer's product name for the sample: 1/2 RHMA-G-SP
The fabricator/manufacturer designation for the sample:
The plant number: 300191
A detailed description of where the material sample was collected: Belt Cut at Blue Diamond Victorville Plant
Where the material sample would have been placed if not sampled: Asphalt Paving
Primary Aggregate Nominal Size: 1/2 inch
The concrete mix design number:
Lot number:
Sublot number:

Test Results

Test 1 of 9

DIME Test ID: 2021-09-21-18-1
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 09/30/2021
Date Tested: 09/24/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test: Combined Virgin Aggregate Gradation
Test Result Compliance:
Additional Comments When Verified:
What type of gradation is being tested? Combined Gradation
Does this test use 1/4 sieve? (question for HMA Gradation Type) No
Cumulative percent passing the 2 in. sieve 100 %
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 100 %
Cumulative percent passing the 1/2 in. sieve 99 %
Cumulative percent passing the 3/8 in. sieve 86 %
Cumulative percent passing the #4 sieve 40 %
Cumulative percent passing the #8 sieve 30 %
Cumulative percent passing the #16 sieve 21 %
Cumulative percent passing the #30 sieve 15 %
Cumulative percent passing the #50 sieve 9 %
Cumulative percent passing the #100 sieve 5 %
Cumulative percent passing the #200 sieve 3.2 %

Test 2 of 9

DIME Test ID: 2021-09-21-18-2
Test Method: AASHTO T84-14: Standard Method of Test for Specific Gravity and Absorption of Fine Aggregate (Fine Specific Gravity)
Verified Date: 09/30/2021
Date Tested: 09/25/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Bulk specific gravity 2.611
Bulk specific gravity (SSD Basis) 2.651
Apparent specific gravity 2.719
Absorption 1.5 %

Test 3 of 9

DIME Test ID: 2021-09-21-18-3
Test Method: AASHTO T85-13: Standard Method of Test for Specific Gravity and Absorption of Coarse Aggregate (Coarse Specific Gravity)
Verified Date: 09/30/2021
Date Tested: 09/25/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Basis for relative density testing Bulk
Specific Gravity 2.688
Absorption 0.7 %

Test 4 of 9

DIME Test ID: 2021-09-21-18-4
Test Method: AASHTO T96-02r10: Standard Method of Test for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine (Los Angeles Rattler)
Verified Date: 09/30/2021
Date Tested: 09/25/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Grading designation C
Mass of sample on No.12 sieve (after 500 revolutions) 3793 grams
Percent loss after 100 revolutions 5 %
Percent loss after 500 revolutions 24 %

Test 5 of 9

DIME Test ID: 2021-09-21-18-5
Test Method: AASHTO T176-08: Standard Method of Test for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test (Sand Equivalent)
Verified Date: 09/30/2021
Date Tested: 09/29/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sand Equivalent 69

Test 6 of 9

DIME Test ID: 2021-09-21-18-6
Test Method: AASHTO T304-11: Standard Method of Test for Uncompacted Void Content of Fine Aggregate (Fine of Crushed Particles)
Verified Date: 09/30/2021
Date Tested: 09/29/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
What test method is performed? Method A
Bulk dry specific gravity 2.611
Average uncompacted voids 43.8 %

Test 7 of 9

DIME Test ID: 2021-09-21-18-7
Test Method: AASHTO T335-09r13: Standard Method of Test for Determining the Percentage of Fracture in Coarse Aggregate (Percent of Crushed Particles)
Verified Date: 09/30/2021
Date Tested: 09/29/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Method 1 - Combined Fracture Determination
Aggregate Size and Fracture Type Coarse 1 and 2 Faced and Fine 1 Faced
Percentage of fractured, coarse, 2 faced particles tested 98 %
Percentage of fractured, coarse, 1 faced particles tested 99 %
Percentage of fractured, fine, 1 faced particles tested 100 %

Test 8 of 9

DIME Test ID: 2021-09-21-18-8
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Verified Date: 09/30/2021
Date Tested: 09/29/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Method B
Determination By Mass
Dimensional ratio used 5:1
Weighted percentage of particles (by mass) that were flat and elongated 2 %
Weighted percentage of particles (by mass) that were not flat and elongated 98 %

Test 9 of 9

DIME Test ID: 2021-09-21-18-9
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 09/30/2021
Date Tested: 09/24/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test: Combined Virgin Aggregate Gradation
Test Result Compliance: does not comply
Additional Comments When Verified:
What type of gradation is being tested? Combined Gradation
Does this test use 1/4 sieve? (question for HMA Gradation Type) No
Cumulative percent passing the 2 in. sieve 100 %
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 100 %
Cumulative percent passing the 1/2 in. sieve 99 %
Cumulative percent passing the 3/8 in. sieve 86 %
Cumulative percent passing the #4 sieve 40 %
Cumulative percent passing the #8 sieve 30 %
Cumulative percent passing the #16 sieve 21 %
Cumulative percent passing the #30 sieve 15 %
Cumulative percent passing the #50 sieve 9 %
Cumulative percent passing the #100 sieve 5 %
Cumulative percent passing the #200 sieve 3.2 %

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.