Print Report | Back to Sample Detail

Sample Record for 2021-08-02-36

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 44444 DEA: ASCP EFIS: ASCP QA Service Level:
DIST-CO-RTE-PM: 59---
Work Description: Special project for submitting Sample information for Asphalt Supplier Certification Program.
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2021-08-02-36
TL Number from the TL Form:
Sample Submitted By Organization: VSS Emultech
Sample Organization Contact: (916) 373-1500
Type of Sample: Quality Control
Type of Material: Asphalt Binder
Sample Taken Date: 08/02/2021
Date that the sample was received by the laboratory/organization performing the testing: 08/02/2021
The quantity of what the sample constitutes: 2 cans, split sample
A brief description of the sample: Asphalt Binder
From where was the sample collected: Manufacturer
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: VSS Emultech West Sac

Material Information

Performance Grade: PG 64-16
Modified: No
Lot number:
Sublot number:
Tank number:
Time of sample:
HMA Supplier:
Asphalt Binder Supplier: VSS Emultech - West Sacramento CA
Multigrade: Yes
Multigrade Type: PG 64-16 / PG 64-10

Test Results

Test 1 of 7

DIME Test ID: 2021-08-02-36-1
Test Method: AASHTO T240-17: Standard Method of Test for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)
Verified Date: 09/07/2021
Date Tested: 08/02/2021
Submitted By Organization: VSS Emultech
Organization Address: 3785 Channel Drive,
Organization City: West Sacramento
Organization State: CA
Organization Zipcode: 95691
Organization Email: jack.dougherty@emultech.com
Organization Phone: (916) 373-1500
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Average mass change -0.232 percent

Test 2 of 7

DIME Test ID: 2021-08-02-36-2
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 09/07/2021
Date Tested: 08/02/2021
Submitted By Organization: VSS Emultech
Organization Address: 3785 Channel Drive,
Organization City: West Sacramento
Organization State: CA
Organization Zipcode: 95691
Organization Email: jack.dougherty@emultech.com
Organization Phone: (916) 373-1500
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Phase Original binder
Test Plate Diameter 25 mm
Phase Angle (δ) (for the 10 cycles) 86.6 degree
Dynamic Shear, G*/sin(δ) 1.37 kPa

Test 3 of 7

DIME Test ID: 2021-08-02-36-3
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 09/07/2021
Date Tested: 08/03/2021
Submitted By Organization: VSS Emultech
Organization Address: 3785 Channel Drive,
Organization City: West Sacramento
Organization State: CA
Organization Zipcode: 95691
Organization Email: jack.dougherty@emultech.com
Organization Phone: (916) 373-1500
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Phase RTFO residue
Test Plate Diameter 25 mm
Phase Angle (δ) (for the 10 cycles) 83.0 degree
Dynamic Shear, G*/sin(δ) 3.42 kPa

Test 4 of 7

DIME Test ID: 2021-08-02-36-4
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 09/07/2021
Date Tested: 08/04/2021
Submitted By Organization: VSS Emultech
Organization Address: 3785 Channel Drive,
Organization City: West Sacramento
Organization State: CA
Organization Zipcode: 95691
Organization Email: jack.dougherty@emultech.com
Organization Phone: (916) 373-1500
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Phase PAV residue
Test Plate Diameter 8 mm
Phase Angle (δ) (for the 10 cycles) 50.6 degree
(G*) x sin(δ)= 2236 kPa

Test 5 of 7

DIME Test ID: 2021-08-02-36-5
Test Method: AASHTO T313-19: Standard Method of Test for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR)
Verified Date: 09/07/2021
Date Tested: 08/04/2021
Submitted By Organization: VSS Emultech
Organization Address: 3785 Channel Drive,
Organization City: West Sacramento
Organization State: CA
Organization Zipcode: 95691
Organization Email: jack.dougherty@emultech.com
Organization Phone: (916) 373-1500
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Time test started no data HH:MM:SS
Flags issued by software during test no data
Correlation coefficient (R²) 0
Regression coefficient a no data
Regression coefficient b no data
Regression coefficient c no data
Load at time 0.0 0.0 mN
Deflection at time 0.0 s 0.000 µm
Load at time 0.5 s 0.0 mN
Deflection at time 0.5 s 0.000 µm
Load at 60.0 s 0.0 mN
Beam deflection 60.0 s 0.000 µm
Measured Stiffness Modulus 60.0 s 60.446 mPa
Estimated Stiffness Modulus 60.0 s no data
Difference between stiffness moduli 60.0 s no data
Estimated m-value 60.0 s 0.397

Test 6 of 7

DIME Test ID: 2021-08-02-36-6
Test Method: AASHTO T316-17: Standard Method of Test for Viscosity Determination of Asphalt Binder Using Rotational Viscometer
Verified Date: 09/07/2021
Date Tested: 08/02/2021
Submitted By Organization: VSS Emultech
Organization Address: 3785 Channel Drive,
Organization City: West Sacramento
Organization State: CA
Organization Zipcode: 95691
Organization Email: jack.dougherty@emultech.com
Organization Phone: (916) 373-1500
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Is viscosity reading in cP/Pa-s? Pa-s
Time of test 10:00 HH:MM
Test Temperature 135 C
Speed 20 rpm
Spindle size 3 in
Torque 19 %
Viscosity reading #1 (A) 0.478 Pa-s
Viscosity reading #2 (B) 0.48 Pa-s
Viscosity reading #3 (C) 0.48 Pa-s
Average viscosity 0.48 Pa-s

Test 7 of 7

DIME Test ID: 2021-08-02-36-7
Test Method: AASHTO T48-18: Standard Method of Test for Flash Point of Asphalt Binder by Cleveland Open Cup
Verified Date: 09/07/2021
Date Tested: 08/02/2021
Submitted By Organization: VSS Emultech
Organization Address: 3785 Channel Drive,
Organization City: West Sacramento
Organization State: CA
Organization Zipcode: 95691
Organization Email: jack.dougherty@emultech.com
Organization Phone: (916) 373-1500
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Units of measurement for Observed Flash Point (C or F) and Ambient barometric pressure (kP or mmHg) Celsius and mmHg
Observed Flash Point 300 C
Ambient Barometric Pressure 760 mmHg
Cleveland Open-Cup Flash Point in Celsius 300 C

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.