Print Report | Back to Sample Detail

Sample Record for 2021-07-12-47

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 44444 DEA: ASCP EFIS: ASCP QA Service Level:
DIST-CO-RTE-PM: 59---
Work Description: Special project for submitting Sample information for Asphalt Supplier Certification Program.
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2021-07-12-47
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Sample Organization Contact: (916) 227-7302
Type of Sample: Quality Control
Type of Material: Asphalt Binder
Sample Taken Date: 07/12/2021
Date that the sample was received by the laboratory/organization performing the testing: 08/05/2021
The quantity of what the sample constitutes: 2 cans
A brief description of the sample: Asphalt binder
From where was the sample collected: Manufacturer
Laboratory sample identification: 071221-761470
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Valero Wilmington

Material Information

Performance Grade: PG 64-16
Modified: No
Lot number:
Sublot number:
Tank number: 10
Time of sample: 1940
HMA Supplier:
Asphalt Binder Supplier: Valero Marketing & Supply - Wilmington CA
Multigrade: Yes
Multigrade Type: PG 64-16 / PG 64-10

Test Results

Test 1 of 5

DIME Test ID: 2021-07-12-47-1
Test Method: AASHTO T240-17: Standard Method of Test for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)
Verified Date: 08/12/2021
Date Tested: 08/10/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Is mass change based on one or two containers? Two
Any material loss from containers during heating process/testing? No
Mass of empty container #1 168.694 grams
Mass of empty container #2 177.192 grams
Mass of container #1 before test (m1i) 204.390 grams
Mass of container #2 before test (m2i) 212.693 grams
Mass of container #1 after test (m1f) 204.252 grams
Mass of container #2 after test (m2f) 212.559 grams
Average mass change -0.382 percent

Test 2 of 5

DIME Test ID: 2021-07-12-47-3
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 08/12/2021
Date Tested: 08/10/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: OG
Test Result Compliance: complies
Additional Comments When Verified:
Phase Original binder
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 12.00 %
Stress Amplitude 0.165 kPa
Phase Angle (δ) (for the 10 cycles) 87.0 degree
Complex Modulus (G*) (for the 10 measurements) 1.377 kPa
Test Temperature 64.0 C
Dynamic Shear, G*/sin(δ) 1.38 kPa

Test 3 of 5

DIME Test ID: 2021-07-12-47-4
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 08/12/2021
Date Tested: 08/10/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: RTFO
Test Result Compliance: complies
Additional Comments When Verified:
Phase RTFO residue
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 10.00 %
Stress Amplitude 0.367 kPa
Phase Angle (δ) (for the 10 cycles) 83.0 degree
Complex Modulus (G*) (for the 10 measurements) 3.675 kPa
Test Temperature 64.0 C
Dynamic Shear, G*/sin(δ) 3.70 kPa

Test 4 of 5

DIME Test ID: 2021-07-12-47-5
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 08/12/2021
Date Tested: 08/11/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: PAV
Test Result Compliance: complies
Additional Comments When Verified:
Phase PAV residue
Test Plate Diameter 8 mm
Test Gap 2 mm
Test Frequency 10.0 rad/s
Strain Amplitude 1.00 %
Stress Amplitude 42.319 kPa
Phase Angle (δ) (for the 10 cycles) 51.6 degree
Complex Modulus (G*) (for the 10 measurements) 4231.320 kPa
Test Temperature 28.0 C
(G*) x sin(δ)= 3316 kPa

Test 5 of 5

DIME Test ID: 2021-07-12-47-6
Test Method: AASHTO T313-19: Standard Method of Test for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR)
Verified Date: 08/12/2021
Date Tested: 08/11/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Minimum test bath temperature at 240 s -6.0 C
Maximum test bath temperature at 240 s -6.0 C
Time of test load application no data HH:MM:SS
File name of test data no data
Time beam in bath no data
Time test started no data HH:MM:SS
Flags issued by software during test no data
Correlation coefficient (R²) 0
Regression coefficient a no data
Regression coefficient b no data
Regression coefficient c no data
Load at time 0.0 0.0 mN
Deflection at time 0.0 s 0.000 µm
Load at time 0.5 s 0.0 mN
Deflection at time 0.5 s 0.000 µm
Load at 60.0 s 945.0 mN
Beam deflection 60.0 s 0.810 µm
Measured Stiffness Modulus 60.0 s 94.000 mPa
Estimated Stiffness Modulus 60.0 s 94.000 mPa
Difference between stiffness moduli 60.0 s no data
Estimated m-value 60.0 s 0.405

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.