Print Report | Back to Sample Detail

Sample Record for 2021-05-24-56

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 215424 DEA: 024G4404 EFIS: 0214000013 QA Service Level: 1
DIST-CO-RTE-PM: 02-SIS-3-38.0/38.6
Work Description: BRIDGE REPLACEMENT
Location Description: SISKIYOU COUNTY ABOUT 6 MILES NORTH OF FORT JONES FROM 0.3 MILE SOUTH TO 0.3 MILE NORTH OF LOWER MOFFETT CREEK ROAD
Contractor Name: Steelhead Constructors
Contractor Address: 2940 INNSBRUCK DRIVE, REDDING CA 96003
Resident Engineer: Nicole Mallory Structure Rep.: Andy O'Sullivan

Sample Information

DIME Sample ID: 2021-05-24-56
TL Number from the TL Form: 897294
Sample Submitted By Organization: CT D02 - North Region Materials Lab
Sample Organization Contact: (530) 225-3194
Type of Sample: Verification
Type of Material: Reclaimed Asphalt Pavement
Sample Taken Date: 05/24/2021
Date that the sample was received by the laboratory/organization performing the testing: 05/24/2021
The quantity of what the sample constitutes: Verification of JMF 21-04-S01
A brief description of the sample: 1/2-inch RAP (Combined)
From where was the sample collected: Manufacturer
Laboratory sample identification: D78807B
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Tullis - Nortstate Asphalt, Redding, CA

Material Information

RAP Source: Tullis, Northstate Asphalt, Redding, CA
Aggregate Size: 1/2-inch
Aggregate Source:
RAP Stockpile:
Stockpile Size (tons):

Test Results

Test 1 of 3

DIME Test ID: 2021-05-24-56-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Asphalt Binder Content)
Verified Date: 08/12/2021
Date Tested: 05/26/2021
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Test procedure used? Method A
Asphalt Binder Content 6.28 %
Mass of HMA prior to ignition 1696.5 g
Mass of aggregate remaining after ignition 1589.9 g
Correction Factor (Percent by mass of HMA Specimen) 0 %
Moisture Content 0 %
Test Temperature 1000 F

Test 2 of 3

DIME Test ID: 2021-05-24-56-2
Test Method: AASHTO T30-19: Standard Method of Test for Mechanical Analysis of Extracted Aggregate (Mechanical Analysis)
Verified Date: 08/12/2021
Date Tested: 05/27/2021
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Does this test use 1/4 sieve? Yes
Total mass of material in the sample 1591.6 grams
Mass retained on the 2 in. sieve 0 grams
Cumulative mass retained on the 1 1/2 in. sieve 0 grams
Cumulative mass retained on the 1 in. sieve 0 grams
Cumulative mass retained on the 3/4 in. sieve 0 grams
Cumulative mass retained on the 1/2 in. sieve 69 grams
Cumulative mass retained on the 3/8 in. sieve 232.5 grams
Mass retained on the 1/4 in. sieve 473.6 grams
Cumulative mass retained on the #4 sieve 603.1 grams
Cumulative mass retained on the #8 sieve 887.5 grams
Cumulative mass retained on the #16 sieve 1083.8 grams
Cumulative mass retained on the #30 sieve 1221 grams
Cumulative mass retained on the #50 sieve 1336 grams
Cumulative mass retained on the #100 sieve 1408.8 grams
Cumulative mass retained on the #200 sieve 1453.1 grams
Cumulative percent passing the 2 in. sieve 100 %
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 100 %
Cumulative percent passing the 1/2 in. sieve 95.7 %
Cumulative percent passing the 3/8 in. sieve 85.4 %
Cumulative percent passing the 1/4 in. sieve 70.2 %
Cumulative percent passing the #4 sieve 62.1 %
Cumulative percent passing the #8 sieve 44.2 %
Cumulative percent passing the #16 sieve 31.9 %
Cumulative percent passing the #30 sieve 23.3 %
Cumulative percent passing the #50 sieve 16.1 %
Cumulative percent passing the #100 sieve 11.5 %
Cumulative percent passing the #200 sieve 8.7 %

Test 3 of 3

DIME Test ID: 2021-05-24-56-3
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 08/12/2021
Date Tested: 05/26/2021
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Number of tests 1
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7336.6 grams
Mass of oven-dry sample in air for Sample 1 1626.3 grams
Mass of container filled with the sample and water for Sample 1 8319.5 grams
Temperature of Water 75 °F
Specific Gravity for Sample 1 2.528

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.