Print Report | Back to Sample Detail

Sample Record for 2021-06-07-25

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 215251 DEA: 021J4604 EFIS: 0220000081 QA Service Level: 1
DIST-CO-RTE-PM: 02-SIS-96-34.5/38.8,88.0/92.0
Work Description: HMA OVERLAY, REPLACE AC SURFACING, SHOULDER BACKING & TRAFFIC STRIPE.
Location Description: SISKIYOU COUNTY NEAR HAPPY CAMP FROM 0.1 MILE EAST OF OAK FLAT CREEK BRIDGE TO 0.1 MILE EAST OF BENJAMIN CREEK ROAD AND FROM 0.3 MILE WEST OF BEAVER CREEK BRIDGE TO 1.0 MILE WEST OF LUMGREY CREEK BRIDGE
Contractor Name: TULLIS, INC.
Contractor Address: 16951 CLEAR CREEK ROAD, REDDING CA 96001
Resident Engineer: Austin Henry Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2021-06-07-25
TL Number from the TL Form: 779370
Sample Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Sample Organization Contact: (530) 225-3194
Type of Sample: Acceptance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 06/07/2021
Date that the sample was received by the laboratory/organization performing the testing: 06/08/2021
The quantity of what the sample constitutes: Production Start-Up Evaluation
A brief description of the sample: Lime Treated 1/2-inch Type A HMA (eq. PG 64-16) with 25.0% RAP and virgin PG 58-22 from Valero - Benicia
From where was the sample collected: Manufacturer
Laboratory sample identification: D78834
Structure unique identifier:
Structure name: Unknown
The fabricator/manufacturer/facility name: Tullis - Northstate Asphalt - Redding, CA

Material Information

HMA Type: Type A HMA
HMA Grading: 1/2 inch
Lot number: 1
Sublot number: 1
HMA Mix Number:

Test Results

Test 1 of 6

DIME Test ID: 2021-06-07-25-1
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 11/30/2021
Date Tested: 06/08/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed Mechanical Agitation - Method A
Mass of container filled with water 7336.6 grams
Mass of oven-dry sample in air for Sample 1 1674.9 grams
Mass of container filled with the sample and water for Sample 1 8345.7 grams
Temperature of Water 76 °F
Specific Gravity for Sample 1 2.516
Theoretical maximum density at 25°C (77°F) no data

Test 2 of 6

DIME Test ID: 2021-06-07-25-2
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 11/30/2021
Date Tested: 06/09/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Bulk Specific Gravity 2.401
Bulk Specific Gravity 2 2.399
Bulk Specific Gravity 3 2.403
Average Bulk Specific Gravity 2.401

Test 3 of 6

DIME Test ID: 2021-06-07-25-3
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 11/30/2021
Date Tested: 06/15/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 193 psi
Average Wet Tensile Strength 173 psi
Tensile Strength Ratio 0.9

Test 4 of 6

DIME Test ID: 2021-06-07-25-4
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 11/30/2021
Date Tested: 08/06/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of the specimen basket assembly no data
Mass of the specimen and specimen basket assembly prior to ignition no data
Mass of HMA Sample prior to ignition 1624.7 g
Corrected Asphalt Binder Content 5.52 %
Mass Loss no data
Mass of aggregate remaining after ignition 1526.4 g
Correction Factor (Percent by mass of HMA Specimen) 0.53 %
Moisture Content 0.00 %
Temperature Compensation Factor no data
Test Temperature 1000 F

Test 5 of 6

DIME Test ID: 2021-06-07-25-5
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 11/30/2021
Date Tested: 06/10/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test: VMA = 15.5%, VFA = 70.5%, DP = 1.2.
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 4.6 %
Percent Air Voids 2 4.7 %
Percent Air Voids 3 4.5 %
Percent Air Voids Average 4.6 %

Test 6 of 6

DIME Test ID: 2021-06-07-25-6
Test Method: AASHTO T324-14: Standard Method of Test for Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures (Hamburg Wheel Track)
Verified Date: 11/30/2021
Date Tested: 06/10/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel A) 20000
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel B) 20000
Impression at specified number of passes, or specified maximum impression if applicable (Wheel A) 2 mm
Impression at specified number of passes, or specified maximum impression if applicable (Wheel B) 2.2 mm
Stripping Inflection Point (Wheel A) >20000
Stripping Inflection Point (Wheel B) >20000