Print Report | Back to Sample Detail

Sample Record for 2021-05-17-3

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214700 DEA: 030F2804 EFIS: 0312000069 QA Service Level: 1
DIST-CO-RTE-PM: 03-SAC-99-7.1/9.4
Work Description: Dillard Overcrossing and McConnel Overhead
Location Description: Hwy 99, Elk Grove, CA
Contractor Name: GRANITE CONSTRUCTION COMPANY
Contractor Address: 4001 Bradshaw Road, Sacramento, CA 95827
Resident Engineer: Saed Masoud Structure Rep.: Chau Ha

Sample Information

DIME Sample ID: 2021-05-17-3
TL Number from the TL Form: C850180
Sample Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Sample Organization Contact: (916) 227-7302
Type of Sample: Verification
Type of Material: Asphalt Binder
Sample Taken Date: 05/17/2021
Date that the sample was received by the laboratory/organization performing the testing: 05/19/2021
The quantity of what the sample constitutes: 1 of 1
A brief description of the sample: pg64-16
From where was the sample collected: Source
Laboratory sample identification: 1550708954
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Granite

Material Information

Performance Grade: PG 64-16
Modified: No
Lot number: 4
Sublot number: 12
Tank number:
Time of sample: 23:59
HMA Supplier:
Asphalt Binder Supplier: Valero Marketing & Supply - Benicia CA
Multigrade: Yes
Multigrade Type:

Test Results

Test 1 of 6

DIME Test ID: 2021-05-17-3-1
Test Method: AASHTO T240-17: Standard Method of Test for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)
Verified Date: 06/01/2021
Date Tested: 05/24/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: per standard specifications
Test Result Compliance: complies
Additional Comments When Verified:
Is mass change based on one or two containers? Two
Any material loss from containers during heating process/testing? No
Mass of empty container #1 171.283 grams
Mass of empty container #2 167.085 grams
Mass of container #1 before test (m1i) 206.590 grams
Mass of container #2 before test (m2i) 202.084 grams
Mass of container #1 after test (m1f) 206.453 grams
Mass of container #2 after test (m2f) 201.943 grams
Average mass change -0.395 percent

Test 2 of 6

DIME Test ID: 2021-05-17-3-2
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 06/01/2021
Date Tested: 05/24/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: per 2018 Standard Specifications ORIG
Test Result Compliance: complies
Additional Comments When Verified:
Phase Original binder
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 12.00 %
Stress Amplitude 0.193 kPa
Phase Angle (δ) (for the 10 cycles) 85.3 degree
Complex Modulus (G*) (for the 10 measurements) 1.612 kPa
Test Temperature 64.0 C
Dynamic Shear, G*/sin(δ) 1.62 kPa

Test 3 of 6

DIME Test ID: 2021-05-17-3-3
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 06/01/2021
Date Tested: 05/24/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: per 2018 Standard Specifications RTFO
Test Result Compliance: complies
Additional Comments When Verified:
Phase RTFO residue
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 10.00 %
Stress Amplitude 0.333 kPa
Phase Angle (δ) (for the 10 cycles) 79.1 degree
Complex Modulus (G*) (for the 10 measurements) 3.327 kPa
Test Temperature 64.0 C
Dynamic Shear, G*/sin(δ) 3.39 kPa

Test 4 of 6

DIME Test ID: 2021-05-17-3-4
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 06/01/2021
Date Tested: 05/26/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: per 2018 Standard Specifications PAV
Test Result Compliance: complies
Additional Comments When Verified:
Phase PAV residue
Test Plate Diameter 8 mm
Test Gap 2 mm
Test Frequency 10.0 rad/s
Strain Amplitude 1.00 %
Stress Amplitude 37.431 kPa
Phase Angle (δ) (for the 10 cycles) 48.1 degree
Complex Modulus (G*) (for the 10 measurements) 3742.800 kPa
Test Temperature 28.0 C
(G*) x sin(δ)= 2786 kPa

Test 5 of 6

DIME Test ID: 2021-05-17-3-5
Test Method: AASHTO T313-19: Standard Method of Test for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR)
Verified Date: 06/01/2021
Date Tested: 05/26/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: per 2018 Standard Specifications
Test Result Compliance: complies
Additional Comments When Verified:
Minimum test bath temperature at 240 s -6.0 C
Maximum test bath temperature at 240 s -5.9 C
Time of test load application no data HH:MM:SS
File name of test data no data
Time beam in bath no data
Time test started no data HH:MM:SS
Flags issued by software during test no data
Correlation coefficient (R²) 0
Regression coefficient a no data
Regression coefficient b no data
Regression coefficient c no data
Load at time 0.0 0.0 mN
Deflection at time 0.0 s 0.000 µm
Load at time 0.5 s 0.0 mN
Deflection at time 0.5 s 0.000 µm
Load at 60.0 s 994.0 mN
Beam deflection 60.0 s 1.149 µm
Measured Stiffness Modulus 60.0 s 69.800 mPa
Estimated Stiffness Modulus 60.0 s 69.800 mPa
Difference between stiffness moduli 60.0 s no data
Estimated m-value 60.0 s 0.397

Test 6 of 6

DIME Test ID: 2021-05-17-3-6
Test Method: AASHTO T240-17: Standard Method of Test for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)
Verified Date: 06/01/2021
Date Tested: 05/24/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: per 2018 Standard Specifications
Test Result Compliance: complies
Additional Comments When Verified:
Is mass change based on one or two containers? Two
Any material loss from containers during heating process/testing? No
Mass of empty container #1 0.000 grams
Mass of empty container #2 0.000 grams
Mass of container #1 before test (m1i) 206.590 grams
Mass of container #2 before test (m2i) 202.084 grams
Mass of container #1 after test (m1f) 206.453 grams
Mass of container #2 after test (m2f) 201.943 grams
Average mass change -0.395 percent

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.