Print Report | Back to Sample Detail

Sample Record for 2021-03-25-13

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 215147 DEA: 060X0404 EFIS: 0618000013 QA Service Level: 1
DIST-CO-RTE-PM: 06-TUL-65,190-0.0/R15.1,8.0/26.5
Work Description: INSTALL RUMBLE STRIPS.
Location Description: TULARE COUNTY NEAR PORTERVILLE ON ROUTE 65 FROM KERN COUNTY LINE TO 0.5 MILE SOUTH OF AVENUE 124 AND ON ROUTE 190 FROM ROAD 180 TO PLEASANT OAK DRIVE
Contractor Name: Global Road Sealing Inc
Contractor Address: 10832 Dorothy Ave, Garden Grove, CA, 92843
Resident Engineer: Jake Garcia Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2021-03-25-13
TL Number from the TL Form: C056403
Sample Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Sample Organization Contact: (916) 227-7302
Type of Sample: Acceptance
Type of Material: Asphalt Binder
Sample Taken Date: 03/25/2021
Date that the sample was received by the laboratory/organization performing the testing: 04/05/2021
The quantity of what the sample constitutes: 1 of 1
A brief description of the sample: Asphalt Binder
From where was the sample collected: Other
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Porterville Asphalt

Material Information

Performance Grade: PG 64-10
Modified: No
Lot number:
Sublot number:
Tank number:
Time of sample:
HMA Supplier: Porterville Asphalt
Asphalt Binder Supplier: San Joaquin Refinery - Bakersfield CA
Multigrade:
Multigrade Type:

Test Results

Test 1 of 5

DIME Test ID: 2021-03-25-13-1
Test Method: AASHTO T240-17: Standard Method of Test for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)
Verified Date: 04/08/2021
Date Tested: 04/06/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: as per 2018 standard specs
Test Result Compliance: complies
Additional Comments When Verified:
Is mass change based on one or two containers? Two
Any material loss from containers during heating process/testing? No
Mass of empty container #1 175.877 grams
Mass of empty container #2 171.130 grams
Mass of container #1 before test (m1i) 213.673 grams
Mass of container #2 before test (m2i) 206.938 grams
Mass of container #1 after test (m1f) 213.534 grams
Mass of container #2 after test (m2f) 206.805 grams
Average mass change -0.370 percent

Test 2 of 5

DIME Test ID: 2021-03-25-13-2
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 04/08/2021
Date Tested: 04/06/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 Std Specs ORIG
Test Result Compliance: complies
Additional Comments When Verified:
Phase Original binder
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 12.00 %
Stress Amplitude 0.159 kPa
Phase Angle (δ) (for the 10 cycles) 88.2 degree
Complex Modulus (G*) (for the 10 measurements) 1.326 kPa
Test Temperature (Specimen 1) 64.0 C
Dynamic Shear, G*/sin(δ) 1.33 kPa

Test 3 of 5

DIME Test ID: 2021-03-25-13-3
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 04/08/2021
Date Tested: 04/06/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 standard specifications RTFO
Test Result Compliance: complies
Additional Comments When Verified:
Phase RTFO residue
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 10.00 %
Stress Amplitude 0.246 kPa
Phase Angle (δ) (for the 10 cycles) 87.6 degree
Complex Modulus (G*) (for the 10 measurements) 2.460 kPa
Test Temperature (Specimen 1) 64.0 C
Dynamic Shear, G*/sin(δ) 2.46 kPa

Test 4 of 5

DIME Test ID: 2021-03-25-13-4
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 04/08/2021
Date Tested: 04/07/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 Std Specs PAV
Test Result Compliance: complies
Additional Comments When Verified:
Phase PAV residue
Test Plate Diameter 8 mm
Test Gap 2 mm
Test Frequency 10.0 rad/s
Strain Amplitude 1.00 %
Stress Amplitude 35.934 kPa
Phase Angle (δ) (for the 10 cycles) 67.2 degree
Complex Modulus (G*) (for the 10 measurements) 3593.354 kPa
Test Temperature (Specimen 1) 31.0 C
(G*) x sin(δ)= 3313 kPa

Test 5 of 5

DIME Test ID: 2021-03-25-13-5
Test Method: AASHTO T313-19: Standard Method of Test for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR)
Verified Date: 04/08/2021
Date Tested: 04/07/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: per 2018 standard specs
Test Result Compliance: complies
Additional Comments When Verified:
Minimum test bath temperature at 240 s 0.0 C
Maximum test bath temperature at 240 s 0.0 C
Time of test load application no data HH:MM:SS
File name of test data no data
Time beam in bath no data
Time test started no data HH:MM:SS
Flags issued by software during test no data
Correlation coefficient (R²) 0
Regression coefficient a no data
Regression coefficient b no data
Regression coefficient c no data
Load at time 0.0 0.0 mN
Deflection at time 0.0 s 0.000 µm
Load at time 0.5 s 0.0 mN
Deflection at time 0.5 s 0.000 µm
Load at 60.0 s 0.0 mN
Beam deflection 60.0 s 0.000 µm
Measured Stiffness Modulus 60.0 s 122.000 mPa
Estimated Stiffness Modulus 60.0 s 122.000 mPa
Difference between stiffness moduli 60.0 s no data
Estimated m-value 60.0 s 0.479

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.