Print Report | Back to Sample Detail

Sample Record for 2021-03-19-12

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214596 DEA: 120R8704 EFIS: 1219000049 QA Service Level: 1
DIST-CO-RTE-PM: 12-ORA-5-25.0/28.3
Work Description: COLD PLANE AC PVMT AND PLACE RHMA.
Location Description: ORANGE COUNTY IN IRVINE AND TUSTIN FROM JEFFREY ROAD OVERCROSSING TO TUSTIN RANCH ROAD UNDERCROSSING
Contractor Name: R J NOBLE COMPANY
Contractor Address: 15505 E Lincoln Ave, Orange, CA 92865
Resident Engineer: Jose Berrios Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2021-03-19-12
TL Number from the TL Form:
Sample Submitted By Organization: CT - Southern Regional Laboratory
Sample Organization Contact: 213-792-4794
Type of Sample: Verification
Type of Material: Aggregate
Sample Taken Date: 03/19/2021
Date that the sample was received by the laboratory/organization performing the testing: 03/29/2021
The quantity of what the sample constitutes: 4 Bags of Coldfeed
A brief description of the sample: JMF 1/2" RWHMA-G-SP, 0.25% Evotherm
From where was the sample collected: Manufacturer
Laboratory sample identification: 0173G-21
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: RJ Noble Orange

Material Information

Source Identification (SMARA or name of Pit): 91-33-0035, 91-33-0039
The fabricator's/manufacturer's product name for the sample: 1/2 RWHMA-G-SP
The fabricator/manufacturer designation for the sample:
The plant number: 50R003ARSPWEO
A detailed description of where the material sample was collected: Belt Cut at RJ Noble Orange Plant
Where the material sample would have been placed if not sampled: Asphalt Paving
Primary Aggregate Nominal Size: 1/2 inch
The concrete mix design number:
Lot number:
Sublot number:

Test Results

Test 1 of 8

DIME Test ID: 2021-03-19-12-1
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 04/15/2021
Date Tested: 04/02/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test: Combined Virgin Aggregate Gradation
Test Result Compliance:
Additional Comments When Verified:
What type of gradation is being tested? Combined Gradation
Does this test use 1/4 sieve? (question for HMA Gradation Type) No
Cumulative percent passing the 2 in. sieve 100 %
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 100 %
Cumulative percent passing the 1/2 in. sieve 97 %
Cumulative percent passing the 3/8 in. sieve 86 %
Cumulative percent passing the #4 sieve 40 %
Cumulative percent passing the #8 sieve 21 %
Cumulative percent passing the #16 sieve 14 %
Cumulative percent passing the #30 sieve 10 %
Cumulative percent passing the #50 sieve 7 %
Cumulative percent passing the #100 sieve 5 %
Cumulative percent passing the #200 sieve 3.6 %

Test 2 of 8

DIME Test ID: 2021-03-19-12-2
Test Method: AASHTO T335-09r13: Standard Method of Test for Determining the Percentage of Fracture in Coarse Aggregate (Percent of Crushed Particles)
Verified Date: 04/15/2021
Date Tested: 04/08/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Method 2 - Individual Fracture Determination
Aggregate Size and Fracture Type Coarse 1 and 2 Faced and Fine 1 Faced
Weighted average percentage of fractured, coarse, 2 faced particles 100 %
Weighted average percentage of fractured, coarse, 1 faced particles 100 %
Percentage of fractured, fine, 1 faced particles tested 100 %

Test 3 of 8

DIME Test ID: 2021-03-19-12-3
Test Method: AASHTO T85-13: Standard Method of Test for Specific Gravity and Absorption of Coarse Aggregate (Coarse Specific Gravity)
Verified Date: 04/15/2021
Date Tested: 04/06/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Basis for relative density testing Bulk
Specific Gravity 2.687
Absorption 0.7 %

Test 4 of 8

DIME Test ID: 2021-03-19-12-4
Test Method: AASHTO T84-14: Standard Method of Test for Specific Gravity and Absorption of Fine Aggregate (Fine Specific Gravity)
Verified Date: 04/15/2021
Date Tested: 04/06/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Bulk specific gravity 2.631
Bulk specific gravity (SSD Basis) 2.672
Apparent specific gravity 2.745
Absorption 1.6 %

Test 5 of 8

DIME Test ID: 2021-03-19-12-5
Test Method: AASHTO T96-02r10: Standard Method of Test for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine (Los Angeles Rattler)
Verified Date: 04/15/2021
Date Tested: 04/06/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Grading designation C
Mass of sample on No.12 sieve (after 500 revolutions) 3817 grams
Percent loss after 100 revolutions 5 %
Percent loss after 500 revolutions 24 %

Test 6 of 8

DIME Test ID: 2021-03-19-12-6
Test Method: AASHTO T176-08: Standard Method of Test for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test (Sand Equivalent)
Verified Date: 04/15/2021
Date Tested: 04/08/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sand Equivalent 68

Test 7 of 8

DIME Test ID: 2021-03-19-12-7
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Verified Date: 04/15/2021
Date Tested: 04/07/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Method B
Determination By Mass
Dimensional ratio used 5:1
Weighted percentage of particles (by mass) that were flat and elongated 6 %
Weighted percentage of particles (by mass) that were not flat and elongated 94 %

Test 8 of 8

DIME Test ID: 2021-03-19-12-8
Test Method: AASHTO T304-11: Standard Method of Test for Uncompacted Void Content of Fine Aggregate (Fine of Crushed Particles)
Verified Date: 04/15/2021
Date Tested: 04/07/2021
Submitted By Organization: CT - Southern Regional Laboratory
Organization Address: 13970 Victoria St,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 213-792-4794
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
What test method is performed? Method A
Bulk dry specific gravity 2.631
Average uncompacted voids 47.7 %

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.