Print Report | Back to Sample Detail

Sample Record for 2021-02-09-20

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 213741 DEA: 07325704 EFIS: 0716000089 QA Service Level: 1
DIST-CO-RTE-PM: 07-LA-5-1.7
Work Description: BUILDING CONSTRUCTION IN LOS ANGELES COUNTY IN SANTA FE SPRINGS AT 14044 FREEWAY DRIVE.
Location Description: Santa Fe Springs, At 14044 Freeway Drive.
Contractor Name: SPECTRUM CONSTRUCTION GROUP, INC.
Contractor Address: 32 EDELMAN, IRVINE CA 92618
Resident Engineer: Mashhur Ali Structure Rep.: Parada, Nelson

Sample Information

DIME Sample ID: 2021-02-09-20
TL Number from the TL Form:
Sample Submitted By Organization: CT QASI - Los Angeles Field Laboratory
Sample Organization Contact: (858) 285-5797
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 02/09/2021
Date that the sample was received by the laboratory/organization performing the testing: 02/15/2021
The quantity of what the sample constitutes: 23
A brief description of the sample: 3/4" x 1 3/4" TC assy
From where was the sample collected: Job Site
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Nucor Fastener Division

Material Information

Rocap Number(s):
Heat Number(s):
Nut Mfg. Lot Number(s): 441443B
Washer Mfg. Lot Number(s): 034081
Bolt Specification: ASTM A325
Bolt Length(s): 1 3/4"
Nut Specification: ASTM A563 Gr DH
Washer Specification: ASTM 436
Finish:
Diameter/Size: 3/4"
Bolt Mfg. Lot Number: 443181C
Rocap Test Requirement(s):
Lubricant Requirements(s):

Test Results

Test 1 of 5

DIME Test ID: 2021-02-09-20-1
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 03/10/2021
Date Tested: 03/03/2021
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test: Nut Proof Load
Additional Comments When Verified:
Number of Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)CommentsTested By
1A441443B61104Nut Proof Loadspaine
UTM 450kip
Temperature 72 f

Test 2 of 5

DIME Test ID: 2021-02-09-20-2
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 03/10/2021
Date Tested: 03/08/2021
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 443181C
Finish Coating Plain
Product Markings A325TC USA N
Size .75 in
Bolt Length 1.75 in
Gage Type Pass

Test 3 of 5

DIME Test ID: 2021-02-09-20-3
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 03/10/2021
Date Tested: 03/08/2021
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 441443B
Finish Coating Plain
Product Markings DH N
Size .75 in
Gage Type Pass

Test 4 of 5

DIME Test ID: 2021-02-09-20-4
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 03/10/2021
Date Tested: 03/08/2021
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 443181C
Finish Coating Plain
Product Markings A325TC USA N
Size .75 in
Bolt Length 1.75 in
Hardness Reading Scale C Scale
Hardness Reading Average 30.6
Spacing Ok

Test 5 of 5

DIME Test ID: 2021-02-09-20-5
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 03/10/2021
Date Tested: 03/08/2021
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 034081
Finish Coating Plain
Product Markings F436 P
Size .75 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 41.25
Spacing Ok

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.