Print Report | Back to Sample Detail

Sample Record for 2021-01-06-9

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 44444 DEA: ASCP EFIS: ASCP QA Service Level:
DIST-CO-RTE-PM: 59---
Work Description: Special project for submitting Sample information for Asphalt Supplier Certification Program.
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2021-01-06-9
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Sample Organization Contact: (916) 227-7302
Type of Sample: Verification
Type of Material: Asphalt Binder
Sample Taken Date: 01/06/2021
Date that the sample was received by the laboratory/organization performing the testing: 01/13/2021
The quantity of what the sample constitutes: 1 of 1
A brief description of the sample: COC Sample
From where was the sample collected: Manufacturer
Laboratory sample identification: 21-006
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Holly Frontier Glendale

Material Information

Performance Grade: PG 58-34 M
Modified: Yes
Lot number:
Sublot number:
Tank number:
Time of sample: 09:30
HMA Supplier:
Asphalt Binder Supplier:
Multigrade:
Multigrade Type:

Test Results

Test 1 of 8

DIME Test ID: 2021-01-06-9-1
Test Method: AASHTO T240-17: Standard Method of Test for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)
Verified Date: 01/25/2021
Date Tested: 01/19/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: per 2018 standard specifications
Test Result Compliance: complies
Additional Comments When Verified:
Is mass change based on one or two containers? Two
Any material loss from containers during heating process/testing? no data
Mass of empty container #1 171.658 grams
Mass of empty container #2 167.959 grams
Mass of container #1 before test (m1i) 207.240 grams
Mass of container #2 before test (m2i) 202.895 grams
Mass of container #1 after test (m1f) 207.148 grams
Mass of container #2 after test (m2f) 202.804 grams
Average mass change -0.260 percent

Test 2 of 8

DIME Test ID: 2021-01-06-9-2
Test Method: AASHTO T301-13: Standard Method of Test for Elastic Recovery Test of Asphalt Materials by Means of a Ductilometer
Verified Date: 01/25/2021
Date Tested: 01/19/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: per 2018 standard specifications
Test Result Compliance: complies
Additional Comments When Verified:
Final Reading from the testing machine (X) 2 cm
% Elongation Recovery 90 %

Test 3 of 8

DIME Test ID: 2021-01-06-9-3
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 01/20/2021
Date Tested: 01/20/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 Std Specs ORIG
Test Result Compliance: complies
Additional Comments When Verified:
Phase Original binder
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 12.00 %
Stress Amplitude 0.188 kPa
Phase Angle (δ) (for the 10 cycles) 62.4 degree
Complex Modulus (G*) (for the 10 measurements) 1.567 kPa
Test Temperature 58.0 C
Dynamic Shear, G*/sin(δ) 1.77 kPa

Test 4 of 8

DIME Test ID: 2021-01-06-9-4
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 01/20/2021
Date Tested: 01/20/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 Std. Spec. RTFO
Test Result Compliance: complies
Additional Comments When Verified:
Phase RTFO residue
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 10.00 %
Stress Amplitude 0.290 kPa
Phase Angle (δ) (for the 10 cycles) 58.7 degree
Complex Modulus (G*) (for the 10 measurements) 2.904 kPa
Test Temperature 58.0 C
Dynamic Shear, G*/sin(δ) 3.40 kPa

Test 5 of 8

DIME Test ID: 2021-01-06-9-5
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 01/25/2021
Date Tested: 01/20/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 Standard Specifications PAV
Test Result Compliance: complies
Additional Comments When Verified:
Phase PAV residue
Test Plate Diameter 8 mm
Test Gap 2 mm
Test Frequency 10.0 rad/s
Strain Amplitude 1.00 %
Stress Amplitude 29.017 kPa
Phase Angle (δ) (for the 10 cycles) 50.5 degree
Complex Modulus (G*) (for the 10 measurements) 2901.738 kPa
Test Temperature 16.0 C
(G*) x sin(δ)= 2239 kPa

Test 6 of 8

DIME Test ID: 2021-01-06-9-6
Test Method: AASHTO T313-19: Standard Method of Test for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR)
Verified Date: 01/25/2021
Date Tested: 01/21/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 Standard Specifications
Test Result Compliance: complies
Additional Comments When Verified:
Minimum test bath temperature at 240 s -24.0 C
Maximum test bath temperature at 240 s -24.0 C
Time of test load application no data HH:MM:SS
File name of test data no data
Time beam in bath no data
Time test started no data HH:MM:SS
Flags issued by software during test no data
Correlation coefficient (R²) 0
Regression coefficient a no data
Regression coefficient b no data
Regression coefficient c no data
Load at time 0.0 0.0 mN
Deflection at time 0.0 s 0.000 µm
Load at time 0.5 s 0.0 mN
Deflection at time 0.5 s 0.000 µm
Load at 60.0 s 0.0 mN
Beam deflection 60.0 s 0.000 µm
Measured Stiffness Modulus 60.0 s 254.000 mPa
Estimated Stiffness Modulus 60.0 s no data
Difference between stiffness moduli 60.0 s no data
Estimated m-value 60.0 s 0.336

Test 7 of 8

DIME Test ID: 2021-01-06-9-8
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 01/20/2021
Date Tested: 01/19/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 Std. Spec.RTFO +6
Test Result Compliance: not applicable
Additional Comments When Verified:
Phase RTFO residue
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 10.00 %
Stress Amplitude 0.173 kPa
Phase Angle (δ) (for the 10 cycles) 59.9 degree
Complex Modulus (G*) (for the 10 measurements) 1.734 kPa
Test Temperature 64.0 C
Dynamic Shear, G*/sin(δ) 2.00 kPa

Test 8 of 8

DIME Test ID: 2021-01-06-9-9
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 01/25/2021
Date Tested: 01/19/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 Std. Spec.RTFO +6
Test Result Compliance: not applicable
Additional Comments When Verified:
Phase RTFO residue
Test Plate Diameter 25 mm
Test Gap no data
Test Frequency 10.0 rad/s
Strain Amplitude 10.00 %
Stress Amplitude 0.173 kPa
Phase Angle (δ) (for the 10 cycles) 59.9 degree
Complex Modulus (G*) (for the 10 measurements) 1.734 kPa
Test Temperature 64.0 C
Dynamic Shear, G*/sin(δ) 2.00 kPa

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.