Print Report | Back to Sample Detail

Sample Record for 2020-08-13-22

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214572 DEA: 034E62U4 EFIS: 0319000068 QA Service Level: 1
DIST-CO-RTE-PM: 03-ED-50-18.5/24.2
Work Description: CONSTRUCT UC, MED BARRIER, DRAINAGE SYSTEMS & HMA OVERLAY.
Location Description: EL DORADO COUNTY IN AND NEAR PLACERVILLE FROM MOSQUITO ROAD UNDERCROSSING TO SCHNELL SCHOOL ROAD UNDERCROSSING AND FROM 0.2 MILE WEST OF STILL MEADOW ROAD TO 0.2 MILE EAST OF CARSON ROAD
Contractor Name: SECURITY PAVING COMPANY, INC.
Contractor Address: 3075 Townsgate Road, Suite 200, Westlake Village, CA 91361
Resident Engineer: Nathan Alterton Structure Rep.: Raymand Macy

Sample Information

DIME Sample ID: 2020-08-13-22
TL Number from the TL Form: c765906
Sample Submitted By Organization: CT D03 - North Region Materials Lab
Sample Organization Contact: (530) 741-4238
Type of Sample: Verification
Type of Material: Aggregate
Sample Taken Date: 08/13/2020
Date that the sample was received by the laboratory/organization performing the testing: 08/14/2020
The quantity of what the sample constitutes: JMF Verification
A brief description of the sample: 3/4 inch HMA - A
From where was the sample collected: Manufacturer
Laboratory sample identification: JMF20-035
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Teichert Aggregates - Grantline Plant

Material Information

Source Identification (SMARA or name of Pit): 91-34-0047
The fabricator's/manufacturer's product name for the sample:
The fabricator/manufacturer designation for the sample:
The plant number:
A detailed description of where the material sample was collected: Batch Plant Hot Bins
Where the material sample would have been placed if not sampled:
Primary Aggregate Nominal Size: 3/4 inch
The concrete mix design number:
Lot number:
Sublot number:

Test Results

Test 1 of 9

DIME Test ID: 2020-08-13-22-1
Test Method: AASHTO T335-09r13: Standard Method of Test for Determining the Percentage of Fracture in Coarse Aggregate (Percent of Crushed Particles)
Verified Date: 12/30/2020
Date Tested: 08/20/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Rd,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-035. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-035
Method 2 - Individual Fracture Determination
Aggregate Size and Fracture Type Coarse 1 and 2 Faced and Fine 1 Faced
Weighted average percentage of fractured, coarse, 2 faced particles 91 %
Weighted average percentage of fractured, coarse, 1 faced particles 97 %
Percentage of fractured, fine, 1 faced particles tested 98 %

Test 2 of 9

DIME Test ID: 2020-08-13-22-2
Test Method: AASHTO T96-02r10: Standard Method of Test for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine (Los Angeles Rattler)
Verified Date: 12/30/2020
Date Tested: 08/20/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Rd,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-035. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-035.
Grading designation C
Percent loss after 100 revolutions 6 %
Percent loss after 500 revolutions 27 %

Test 3 of 9

DIME Test ID: 2020-08-13-22-3
Test Method: AASHTO T176-08: Standard Method of Test for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test (Sand Equivalent)
Verified Date: 12/30/2020
Date Tested: 08/17/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Rd,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-035. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-035
Sand Equivalent 78

Test 4 of 9

DIME Test ID: 2020-08-13-22-4
Test Method: AASHTO T304-11: Standard Method of Test for Uncompacted Void Content of Fine Aggregate (Fine of Crushed Particles)
Verified Date: 12/30/2020
Date Tested: 08/20/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Rd,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-035. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-035.
What test method is performed? Method A
Bulk dry specific gravity 2.674
Average uncompacted voids 48.5 %

Test 5 of 9

DIME Test ID: 2020-08-13-22-5
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Verified Date: 12/30/2020
Date Tested: 08/19/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Rd,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-035. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-035.
Method B
Determination By Mass
Dimensional ratio used 5:1
Weighted percentage of particles (by mass) that were flat and elongated 4 %
Weighted percentage of particles (by mass) that were not flat and elongated 96 %

Test 6 of 9

DIME Test ID: 2020-08-13-22-6
Test Method: CTM 204-June 2010: Method of Test for Liquid Limit, Plastic Limit and Plasticity Index of Soils (Plasticity Index)
Verified Date: 12/30/2020
Date Tested: 08/19/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Rd,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-035. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-035
Plastic Index(PI) NP
Liquid Limit (LL) 0 %
Plastic Limit (PL) 0 %

Test 7 of 9

DIME Test ID: 2020-08-13-22-7
Test Method: AASHTO T85-13: Standard Method of Test for Specific Gravity and Absorption of Coarse Aggregate (Coarse Specific Gravity)
Verified Date: 12/30/2020
Date Tested: 08/18/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Rd,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-035. Test date estimated.
Test Result Compliance: not applicable
Additional Comments When Verified: JMF20-035
Basis for relative density testing Bulk
Specific Gravity 2.693
Absorption 1.4 %

Test 8 of 9

DIME Test ID: 2020-08-13-22-8
Test Method: AASHTO T84-14: Standard Method of Test for Specific Gravity and Absorption of Fine Aggregate (Fine Specific Gravity)
Verified Date: 12/30/2020
Date Tested: 08/18/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Rd,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-035. Test date estimated.
Test Result Compliance: not applicable
Additional Comments When Verified: JMF20-035
Bulk specific gravity 2.674
Bulk specific gravity (SSD Basis) 2.717
Apparent specific gravity 2.794
Absorption 1.6 %

Test 9 of 9

DIME Test ID: 2020-08-13-22-9
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 12/30/2020
Date Tested: 08/17/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Rd,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-035. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified: JMF20-035
What type of gradation is being tested? HMA Gradation
Does this test use 1/4 sieve? (question for HMA Gradation Type) No
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 99 %
Cumulative percent passing the 1/2 in. sieve 85 %
Cumulative percent passing the 3/8 in. sieve 72 %
Cumulative percent passing the #4 sieve 49 %
Cumulative percent passing the #8 sieve 36 %
Cumulative percent passing the #16 sieve 27 %
Cumulative percent passing the #30 sieve 20 %
Cumulative percent passing the #50 sieve 13 %
Cumulative percent passing the #100 sieve 8 %
Cumulative percent passing the #200 sieve 3.9 %

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.