Print Report | Back to Sample Detail

Sample Record for 2020-04-17-17

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214628 DEA: 031G6604 EFIS: 0319000116 QA Service Level: 1
DIST-CO-RTE-PM: 03-BUT-162-12.6/15.6
Work Description: COLD IN-PLACE RECYCLING, RHMA-G OVERLAY, AND COLD PLANE AC PAVEMENT.
Location Description: BUTTE COUNTY IN AND NEAR OROVILLE FROM 0.8 MILE EAST OF WILBUR ROAD TO FEATHER RIVER BRIDGE
Contractor Name: LAMON CONSTRUCTION
Contractor Address: 871 Von Geldern Way, Yuba City, California 95991
Resident Engineer: Ryan Johnson Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2020-04-17-17
TL Number from the TL Form: C779100
Sample Submitted By Organization: CT D03 - North Region Materials Lab
Sample Organization Contact: (530) 741-4238
Type of Sample: Verification
Type of Material: Aggregate
Sample Taken Date: 04/17/2020
Date that the sample was received by the laboratory/organization performing the testing: 04/20/2020
The quantity of what the sample constitutes: JMF Verification
A brief description of the sample: 1/2 inch RHMA-G
From where was the sample collected: Manufacturer
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Teichert-Hallwood Drum Plant

Material Information

Source Identification (SMARA or name of Pit): 91-58-0006::HALLWOOD PLANT
The fabricator's/manufacturer's product name for the sample:
The fabricator/manufacturer designation for the sample:
The plant number:
A detailed description of where the material sample was collected: cold feed
Where the material sample would have been placed if not sampled:
Primary Aggregate Nominal Size: 1/2 inch
The concrete mix design number:
Lot number:
Sublot number:

Test Results

Test 1 of 10

DIME Test ID: 2020-04-17-17-1
Test Method: AASHTO T335-09r13: Standard Method of Test for Determining the Percentage of Fracture in Coarse Aggregate (Percent of Crushed Particles)
Verified Date: 11/12/2020
Date Tested: 05/26/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017. Test Date Estimated
Test Result Compliance: complies
Additional Comments When Verified:
Method 2 - Individual Fracture Determination
Aggregate Size and Fracture Type Coarse 1 and 2 Faced and Fine 1 Faced
Weighted average percentage of fractured, coarse, 2 faced particles 91 %
Weighted average percentage of fractured, coarse, 1 faced particles 96 %
Percentage of fractured, fine, 1 faced particles tested 99 %

Test 2 of 10

DIME Test ID: 2020-04-17-17-2
Test Method: AASHTO T96-02r10: Standard Method of Test for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine (Los Angeles Rattler)
Verified Date: 11/12/2020
Date Tested: 05/26/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017. Test Date Estimated
Test Result Compliance: complies
Additional Comments When Verified:
Grading designation C
Percent loss after 100 revolutions 5 %
Percent loss after 500 revolutions 23 %

Test 3 of 10

DIME Test ID: 2020-04-17-17-3
Test Method: AASHTO T176-08: Standard Method of Test for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test (Sand Equivalent)
Verified Date: 11/12/2020
Date Tested: 05/26/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017. Test Date Estimated. Only average (83) Provided by lab
Test Result Compliance: complies
Additional Comments When Verified: JMF20-017
Sand Equivalent 83

Test 4 of 10

DIME Test ID: 2020-04-17-17-4
Test Method: AASHTO T304-11: Standard Method of Test for Uncompacted Void Content of Fine Aggregate (Fine of Crushed Particles)
Verified Date: 11/12/2020
Date Tested: 05/26/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017. Test date estimated.
Test Result Compliance: not applicable
Additional Comments When Verified:
What test method is performed? Method A
Bulk dry specific gravity 2.691
Average uncompacted voids 46.6 %

Test 5 of 10

DIME Test ID: 2020-04-17-17-5
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Verified Date: 11/12/2020
Date Tested: 05/26/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017. Test Date Estimated
Test Result Compliance: complies
Additional Comments When Verified: JMF20-017
Method B
Determination By Mass
Dimensional ratio used 5:1
Weighted percentage of particles (by mass) that were flat and elongated 1 %
Weighted percentage of particles (by mass) that were not flat and elongated 99 %

Test 6 of 10

DIME Test ID: 2020-04-17-17-6
Test Method: CTM 204-June 2010: Method of Test for Liquid Limit, Plastic Limit and Plasticity Index of Soils (Plasticity Index)
Verified Date: 11/12/2020
Date Tested: 05/26/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017. Test Date Estimated
Test Result Compliance: complies
Additional Comments When Verified: JMF20-017
Plastic Index(PI) NP
Liquid Limit (LL) 0 %
Plastic Limit (PL) 0 %

Test 7 of 10

DIME Test ID: 2020-04-17-17-7
Test Method: AASHTO T85-13: Standard Method of Test for Specific Gravity and Absorption of Coarse Aggregate (Coarse Specific Gravity)
Verified Date: 11/13/2020
Date Tested: 05/26/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017. Test date estimated
Test Result Compliance: not applicable
Additional Comments When Verified: JMF20-017
Basis for relative density testing Bulk
Specific Gravity 2.742
Absorption 0.9 %

Test 8 of 10

DIME Test ID: 2020-04-17-17-8
Test Method: AASHTO T84-14: Standard Method of Test for Specific Gravity and Absorption of Fine Aggregate (Fine Specific Gravity)
Verified Date: 11/13/2020
Date Tested: 05/26/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017. Test date estimated
Test Result Compliance: not applicable
Additional Comments When Verified: JMF20-017
Bulk specific gravity 2.691
Bulk specific gravity (SSD Basis) 2.735
Apparent specific gravity 2.816
Absorption 1.7 %

Test 9 of 10

DIME Test ID: 2020-04-17-17-9
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 11/13/2020
Date Tested: 05/26/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017. Test date estimated
Test Result Compliance: complies
Additional Comments When Verified: JMF20-017
What type of gradation is being tested? HMA Gradation
Does this test use 1/4 sieve? (question for HMA Gradation Type) No
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 100 %
Cumulative percent passing the 1/2 in. sieve 99 %
Cumulative percent passing the 3/8 in. sieve 92 %
Cumulative percent passing the #4 sieve 39 %
Cumulative percent passing the #8 sieve 22 %
Cumulative percent passing the #16 sieve 15 %
Cumulative percent passing the #30 sieve 11 %
Cumulative percent passing the #50 sieve 8 %
Cumulative percent passing the #100 sieve 5 %
Cumulative percent passing the #200 sieve 3.3 %

Test 10 of 10

DIME Test ID: 2020-04-17-17-10
Test Method: AASHTO T304-11: Standard Method of Test for Uncompacted Void Content of Fine Aggregate (Fine of Crushed Particles)
Verified Date: 11/12/2020
Date Tested: 05/26/2020
Submitted By Organization: CT D03 - North Region Materials Lab
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017. Test date estimated.
Test Result Compliance: complies
Additional Comments When Verified:
What test method is performed? Method A
Bulk dry specific gravity 2.691
Average uncompacted voids 46.6 %

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.