Print Report | Back to Sample Detail

Sample Record for 2020-06-10-31

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214589 DEA: 020J1604 QA Service Level: 1
DIST-CO-RTE-PM: 02-PLU-284-0.0/8.3
Work Description: PLACE HMA (TYPE A), PRECOATED AGGREGATE (SEAL COAT), HMA (LEVELING).
Location Description: PLUMAS COUNTY NEAR CHILCOOT FROM ROUTE 70 TO 1 MILE NORTH OF LITTLE LAST CHANCE CREEK BRIDGE NUMBER 09-0072
Contractor Name: HAT CREEK CONSTRUCTION & MATERIALS, INC.
Contractor Address: 24339 STATE HIGHWAY 89 N.;, BURNEY CA 96013
Resident Engineer: Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2020-06-10-31
TL Number from the TL Form: 896983
Sample Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Sample Organization Contact: (530) 225-3194
Type of Sample: Verification
Type of Material: Aggregate
Sample Taken Date: 06/10/2020
Date that the sample was received by the laboratory/organization performing the testing: 06/11/2020
The quantity of what the sample constitutes: JMF Verification
A brief description of the sample: Washed Dust Sized Untreated Virgin Aggregate
From where was the sample collected: Source
Laboratory sample identification: D78468C 20-05
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Ward Lake Pit

Material Information

Source Identification (SMARA, name of Pit or Job Site): 91-18-0008
The fabricator's/manufacturer's product name for the sample: Unknown
The fabricator/manufacturer designation for the sample: Unknown
The plant number: Unknown
A detailed description of where the material sample was collected: Sized Untreated Aggregate Stockpile
Where the material sample would have been placed if not sampled: Unknown
Primary Aggregate Nominal Size: 1/4 inch
The concrete mix design number: JMF 20-05-S1a
Lot number: Unknown
Sublot number: Unknown
Aggregate Mix Number:

Test Results

Test 1 of 1

DIME Test ID: 2020-06-10-31-1
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 07/06/2020
Date Tested: 06/15/2020
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
What type of gradation is being tested? HMA Gradation
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 100 %
Cumulative percent passing the 1/2 in. sieve 100 %
Cumulative percent passing the 3/8 in. sieve 100 %
Cumulative percent passing the 1/4 in. sieve 99.1 %
Cumulative percent passing the #4 sieve 89.9 %
Cumulative percent passing the #8 sieve 53.3 %
Cumulative percent passing the #16 sieve 31.2 %
Cumulative percent passing the #30 sieve 17.7 %
Cumulative percent passing the #50 sieve 9.4 %
Cumulative percent passing the #100 sieve 4.3 %
Cumulative percent passing the #200 sieve 2.51 %