Print Report | Back to Sample Detail

Sample Record for 2019-10-31-14

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214141 DEA: 081J1204 EFIS: 0817000208 QA Service Level: 1
DIST-CO-RTE-PM: 08-RIV-15,91,215-Var
Work Description: REMOVE, PREPARE AND FURNISH POLYESTER CONCRETE OVERLAY.
Location Description: RIVERSIDE COUNTY AT VARIOUS LOCATIONS
Contractor Name: J. FRANCIS COMPANY
Contractor Address: 16197 Krameria Ave., Riverside, CA 92504
Resident Engineer: Xavier Avila Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2019-10-31-14
TL Number from the TL Form: C719377
Sample Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Sample Organization Contact: (530) 329-6527
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 10/31/2019
Date that the sample was received by the laboratory/organization performing the testing: 11/14/2019
The quantity of what the sample constitutes: 4
A brief description of the sample: A325 Bolt
From where was the sample collected: Manufacturer
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Midwest Structural Products

Material Information

Rocap Number(s):
Heat Number(s): 100896901 DL18101165 211887
Nut Mfg. Lot Number(s): 406871A
Washer Mfg. Lot Number(s): C6542D
Bolt Specification: A325
Bolt Length(s): 2.25"
Nut Specification: A563
Washer Specification: F436
Finish: HDG
Diameter/Size: .75"
Bolt Mfg. Lot Number: 424370B
Rocap Test Requirement(s):
Lubricant Requirements(s):
Test results on following page(s): 8

Test Results

Test 1 of 8

DIME Test ID: 2019-10-31-14-1
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 11/15/2019
Date Tested: 11/14/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A563 DH Nut
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)CommentsTested By
1406871A51042A563 DH Nutfsaylor
UTM 450kip
Temperature 72 f

Test 2 of 8

DIME Test ID: 2019-10-31-14-2
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 11/15/2019
Date Tested: 11/14/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 406871A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size .75 in
Gage Type Pass

Test 3 of 8

DIME Test ID: 2019-10-31-14-3
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 11/15/2019
Date Tested: 11/14/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 424370B
Finish Coating ASTM F2329 - Hot Dip
Product Markings QA325 USA N
Size .75 in
Bolt Length 2.250 in
Gage Type Pass

Test 4 of 8

DIME Test ID: 2019-10-31-14-4
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/15/2019
Date Tested: 11/14/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 424370B
Finish Coating ASTM F2329 - Hot Dip
Product Markings QA325 USA N
Size .75 in
Bolt Length 2.250 in
Measurement Average 6.12 mils

Test 5 of 8

DIME Test ID: 2019-10-31-14-5
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/15/2019
Date Tested: 11/14/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 406871A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size .75 in
Bolt Length no data in
Measurement Average 4.08 mils

Test 6 of 8

DIME Test ID: 2019-10-31-14-6
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/15/2019
Date Tested: 11/14/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number C6542D
Finish Coating ASTM F2329 - Hot Dip
Product Markings P F436
Size .75 in
Bolt Length no data in
Measurement Average 4.7 mils

Test 7 of 8

DIME Test ID: 2019-10-31-14-7
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 11/15/2019
Date Tested: 11/14/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 424370B
Finish Coating ASTM F2329 - Hot Dip
Product Markings QA325 USA N
Size .75 in
Bolt Length 2.250 in
Hardness Reading Scale C Scale
Hardness Reading Average 27.58
Spacing Ok

Test 8 of 8

DIME Test ID: 2019-10-31-14-8
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 11/15/2019
Date Tested: 11/14/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number C6542D
Finish Coating ASTM F2329 - Hot Dip
Product Markings P F436
Size .75 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 35.4
Spacing Ok