Print Report | Back to Sample Detail

Sample Record for 2019-08-08-21

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 213261 DEA: 071XH004 EFIS: 0718000239 QA Service Level: 1
DIST-CO-RTE-PM: 07-LA-47-.86, 0.86, 0.86
Work Description: Remove and replace the two (2) long finger joint assemblies at Bents 11 and 12 and repair the elevators in both towers
Location Description:
Contractor Name: GOLDEN STATE BRIDGE INC
Contractor Address: 3701 Mallard Dr., Benicia, CA 94510
Resident Engineer: Thang Ton Structure Rep.: Noah Bruton

Sample Information

DIME Sample ID: 2019-08-08-21
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - QASI Sacramento Field Office
Sample Organization Contact: (916) 2058871
Type of Sample: Acceptance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 08/08/2019
Date that the sample was received by the laboratory/organization performing the testing: 08/09/2019
The quantity of what the sample constitutes: 110
A brief description of the sample: 7/8 - 9 x 7 A325
From where was the sample collected: Fabricator
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: CK Johnson

Material Information

Rocap Number(s): 812525R
Heat Number(s): 10550960, 21807850, DL18101099
Nut Mfg. Lot Number(s): 406805A
Washer Mfg. Lot Number(s): D5899
Bolt Specification: A325
Bolt Length(s): 7"
Nut Specification: A563
Washer Specification: F436
Finish: HDG
Diameter/Size: 7/8 - 9
Bolt Mfg. Lot Number: 812525
Rocap Test Requirement(s): Yes
Lubricant Requirements(s): Yes

Test Results

Test 1 of 18

DIME Test ID: 2019-08-08-21-1
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 08/22/2019
Date Tested: 08/20/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
1A8125250.875066683296.6210.00spaine
UTM 450kip
Temperature no data

Test 2 of 18

DIME Test ID: 2019-08-08-21-2
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 812525
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size .875 in
Bolt Length 7 in
Gage Type Pass

Test 3 of 18

DIME Test ID: 2019-08-08-21-3
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 812525
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size .875 in
Bolt Length 7 in
Gage Type Pass

Test 4 of 18

DIME Test ID: 2019-08-08-21-4
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 812525
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size .875 in
Bolt Length 7 in
Gage Type Pass

Test 5 of 18

DIME Test ID: 2019-08-08-21-5
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 406805A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size .875 in
Gage Type Pass

Test 6 of 18

DIME Test ID: 2019-08-08-21-6
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 406805A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size .875 in
Gage Type Pass

Test 7 of 18

DIME Test ID: 2019-08-08-21-7
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 406805A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size .875 in
Gage Type Pass

Test 8 of 18

DIME Test ID: 2019-08-08-21-8
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 812525
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size .875 in
Bolt Length 7 in
Measurement Average 3.83 mils

Test 9 of 18

DIME Test ID: 2019-08-08-21-9
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 812525
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size .875 in
Bolt Length 7 in
Measurement Average 3.55 mils

Test 10 of 18

DIME Test ID: 2019-08-08-21-10
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 812525
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 USA LE
Size .875 in
Bolt Length 7 in
Measurement Average 3.68 mils

Test 11 of 18

DIME Test ID: 2019-08-08-21-11
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 406805A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size .875 in
Bolt Length no data in
Measurement Average 3.1 mils

Test 12 of 18

DIME Test ID: 2019-08-08-21-12
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 406805A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size .875 in
Bolt Length no data in
Measurement Average 2.43 mils

Test 13 of 18

DIME Test ID: 2019-08-08-21-13
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 406805A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size .875 in
Bolt Length no data in
Measurement Average 3.66 mils

Test 14 of 18

DIME Test ID: 2019-08-08-21-14
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number D5899
Finish Coating ASTM F2329 - Hot Dip
Product Markings F436 P
Size .875 in
Bolt Length no data in
Measurement Average 4.24 mils

Test 15 of 18

DIME Test ID: 2019-08-08-21-15
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number D5899
Finish Coating ASTM F2329 - Hot Dip
Product Markings F436 P
Size .875 in
Bolt Length no data in
Measurement Average 2.34 mils

Test 16 of 18

DIME Test ID: 2019-08-08-21-16
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number D5899
Finish Coating ASTM F2329 - Hot Dip
Product Markings F436 P
Size .875 in
Bolt Length no data in
Measurement Average 3.73 mils

Test 17 of 18

DIME Test ID: 2019-08-08-21-17
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number D5899
Finish Coating ASTM F2329 - Hot Dip
Product Markings F436 P
Size .875 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 38.75
Spacing Ok

Test 18 of 18

DIME Test ID: 2019-08-08-21-18
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 08/22/2019
Date Tested: 08/21/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number D5899
Finish Coating ASTM F2329 - Hot Dip
Product Markings F436 P
Size .875 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 41.3
Spacing Ok