Print Report | Back to Sample Detail

Sample Record for 2019-08-08-8

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

DEA: No Project QA Service Level:
DIST-CO-RTE-PM: ---
Work Description: Special project identifier for material not associated with a project
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2019-08-08-8
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - QASI Los Angeles Field Office
Sample Organization Contact: (858) 285-5797
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 08/08/2019
Date that the sample was received by the laboratory/organization performing the testing: 08/14/2019
The quantity of what the sample constitutes: 9
A brief description of the sample: 1-1/2"" x 5-1/2" HS Bolt Assys
From where was the sample collected: Fabricator
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: UIS Lindon UT

Material Information

Rocap Number(s): TT0031885
Heat Number(s): 62134200 M669280 235580
Nut Mfg. Lot Number(s): TL481
Washer Mfg. Lot Number(s): C7027M
Bolt Specification: ASTM A325
Bolt Length(s): 5-1/2"
Nut Specification: ASTM A563 Grade DH
Washer Specification: ASTM F436
Finish: Mechanically Galvanized
Diameter/Size: 1-1/2"
Bolt Mfg. Lot Number: 037492
Rocap Test Requirement(s): Test 2 Samples
Lubricant Requirements(s): NA
Test results on following page(s): 17

Test Results

Test 1 of 17

DIME Test ID: 2019-08-08-8-1
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
1A0374921.5000177517789.636.00spaine
UTM 450kip
Temperature no data

Test 2 of 17

DIME Test ID: 2019-08-08-8-2
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 037492
Finish Coating ASTM B695 - Mech Galv
Product Markings SL A325 B
Size 1.5 in
Bolt Length 5.5 in
Gage Type Pass

Test 3 of 17

DIME Test ID: 2019-08-08-8-3
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 037492
Finish Coating ASTM B695 - Mech Galv
Product Markings SL A325 B
Size 1.5 in
Bolt Length 5.5 in
Gage Type Pass

Test 4 of 17

DIME Test ID: 2019-08-08-8-4
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 037492
Finish Coating ASTM B695 - Mech Galv
Product Markings SL A325 B
Size 1.5 in
Bolt Length 5.5 in
Gage Type Pass

Test 5 of 17

DIME Test ID: 2019-08-08-8-8
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 037492
Finish Coating ASTM B695 - Mech Galv
Product Markings SL A325 B
Size 1.5 in
Bolt Length 5.5 in
Measurement Average 8.71 mils

Test 6 of 17

DIME Test ID: 2019-08-08-8-9
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 037492
Finish Coating ASTM B695 - Mech Galv
Product Markings SL A325 B
Size 1.5 in
Bolt Length 5.5 in
Measurement Average 7.69 mils

Test 7 of 17

DIME Test ID: 2019-08-08-8-10
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 037492
Finish Coating ASTM B695 - Mech Galv
Product Markings SL A325 B
Size 1.5 in
Bolt Length 5.5 in
Measurement Average 6.55 mils

Test 8 of 17

DIME Test ID: 2019-08-08-8-11
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number TL481
Finish Coating ASTM B695 - Mech Galv
Product Markings DH U
Size 1.5 in
Bolt Length no data in
Measurement Average 4.29 mils

Test 9 of 17

DIME Test ID: 2019-08-08-8-12
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number TL481
Finish Coating ASTM B695 - Mech Galv
Product Markings DH U
Size 1.5 in
Bolt Length no data in
Measurement Average 2.93 mils

Test 10 of 17

DIME Test ID: 2019-08-08-8-13
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number TL481
Finish Coating ASTM B695 - Mech Galv
Product Markings DH U
Size 1.5 in
Bolt Length no data in
Measurement Average 2.63 mils

Test 11 of 17

DIME Test ID: 2019-08-08-8-14
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number C7027M
Finish Coating ASTM B695 - Mech Galv
Product Markings F436 P
Size 1.5 in
Bolt Length no data in
Measurement Average 3.31 mils

Test 12 of 17

DIME Test ID: 2019-08-08-8-15
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number C7027M
Finish Coating ASTM B695 - Mech Galv
Product Markings F436 P
Size 1.5 in
Bolt Length no data in
Measurement Average 3.42 mils

Test 13 of 17

DIME Test ID: 2019-08-08-8-16
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number C7027M
Finish Coating ASTM B695 - Mech Galv
Product Markings F436 P
Size 1.5 in
Bolt Length no data in
Measurement Average 3.57 mils

Test 14 of 17

DIME Test ID: 2019-08-08-8-17
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number TL481
Finish Coating ASTM B695 - Mech Galv
Product Markings DH U
Size 1.5 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 30.17
Spacing Ok

Test 15 of 17

DIME Test ID: 2019-08-08-8-18
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number TL481
Finish Coating ASTM B695 - Mech Galv
Product Markings DH U
Size 1.5 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 27.8
Spacing Ok

Test 16 of 17

DIME Test ID: 2019-08-08-8-19
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number C7027M
Finish Coating ASTM B695 - Mech Galv
Product Markings F436 P
Size 1.5 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 42.85
Spacing Ok

Test 17 of 17

DIME Test ID: 2019-08-08-8-20
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 08/30/2019
Date Tested: 08/27/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number C7027M
Finish Coating ASTM B695 - Mech Galv
Product Markings F436 P
Size 1.5 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 42.4
Spacing Ok