Print Report | Back to Sample Detail

Sample Record for 2019-04-17-3

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

DEA: No Project QA Service Level:
DIST-CO-RTE-PM: ---
Work Description: Special project identifier for material not associated with a project
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2019-04-17-3
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - QASI Bay Area Field Office
Sample Organization Contact: (916) 284-6784
Type of Sample: Verification
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 04/17/2019
Date that the sample was received by the laboratory/organization performing the testing: 04/19/2019
The quantity of what the sample constitutes: 3
A brief description of the sample: 7/8" x 17 1/2" A449 HDG anchor bolt
From where was the sample collected: Fabricator
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: UIS

Material Information

Rocap Number(s): none
Heat Number(s): 189037
Nut Mfg. Lot Number(s): n/a
Washer Mfg. Lot Number(s): n/a
Bolt Specification: A449 HDG
Bolt Length(s): 17 1/2"
Nut Specification: n/a
Washer Specification: n/a
Finish: HDG
Diameter/Size: 7/8"
Bolt Mfg. Lot Number: Rockford
Rocap Test Requirement(s): none
Lubricant Requirements(s): none
Test results on following page(s): 7

Test Results

Test 1 of 7

DIME Test ID: 2019-04-17-3-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 05/01/2019
Date Tested: 04/30/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A449 Bolt
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleSizeArea (in^2)Peak Load (lbf)Peak Load (kN)Tensile Strength (psi)Stress at Offset (psi)Load at Offset (lbf)Comments
1AA449 7/8 x 17.5 Bolt 10 Deg Wedge0.4626347528213739212681658589A449 Bolt
UTM 400KIP
Temperature 72

Test 2 of 7

DIME Test ID: 2019-04-17-3-2
Test Method: ASME B1.2-83r01: (Pitch Diameter) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Pitch Diameter)
Verified Date: 05/01/2019
Date Tested: 05/01/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 189037
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .875 in
Bolt Length 17.5 in
Pitch Diameter .809 in
Pitch Diameter 2nd .809 in

Test 3 of 7

DIME Test ID: 2019-04-17-3-3
Test Method: ASME B1.2-83r01: (Pitch Diameter) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Pitch Diameter)
Verified Date: 05/01/2019
Date Tested: 05/01/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) 189037
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .875 in
Bolt Length 17.5 in
Pitch Diameter .809 in
Pitch Diameter 2nd .809 in

Test 4 of 7

DIME Test ID: 2019-04-17-3-4
Test Method: ASME B1.2-83r01: (Pitch Diameter) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Pitch Diameter)
Verified Date: 05/01/2019
Date Tested: 05/01/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) 189037
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .875 in
Bolt Length 17.5 in
Pitch Diameter .811 in
Pitch Diameter 2nd .811 in

Test 5 of 7

DIME Test ID: 2019-04-17-3-5
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/01/2019
Date Tested: 05/01/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 189037
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .875 in
Bolt Length 17.5 in
Measurement Average 3.44 mils

Test 6 of 7

DIME Test ID: 2019-04-17-3-6
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/01/2019
Date Tested: 05/01/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) 189037
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .875 in
Bolt Length 17.5 in
Measurement Average 2.83 mils

Test 7 of 7

DIME Test ID: 2019-04-17-3-7
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/01/2019
Date Tested: 05/01/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) 189037
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449 01AE
Size .875 in
Bolt Length 17.5 in
Measurement Average 3.37 mils