Print Report | Back to Sample Detail

Sample Record for 2018-09-22-6

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 213134 DEA: 024F77U4 EFIS: 0217000022 QA Service Level: 1
DIST-CO-RTE-PM: 02-MOD-299-23.1/23.6, 24.5/33.5
Work Description: BRIDGE REPLACE, ROADWAY REHAB/FULL DEPTH RECLAMATION-CEMENT + HMA
Location Description: MODOC COUNTY ABOUT 6 MILES WEST OF ALTURAS FROM 0.3 MILE WEST TO 0.3 MILE EAST OF CALDWELL CREEK BRIDGE AND 1.1 MILES EAST OF CALDWELL CREEK BRIDGE TO 1.7 MILES WEST OF COUNTY ROAD 75
Contractor Name: Hat Creek Construction & Materials, Incorporated
Contractor Address: 24339 Highway 89 N, Burney, CA 96013
Resident Engineer: Mike Zdenek Structure Rep.: Ryan Duran

Sample Information

DIME Sample ID: 2018-09-22-6
TL Number from the TL Form: 852918
Sample Submitted By Organization: CT D02 - North Region Materials Lab
Sample Organization Contact: (530) 225-3194
Type of Sample: Verification
Type of Material: Aggregate
Sample Taken Date: 09/22/2018
Date that the sample was received by the laboratory/organization performing the testing: 09/22/2018
The quantity of what the sample constitutes: JMF Verification
A brief description of the sample: Combined Virgin Aggregate
From where was the sample collected: Manufacturer
Laboratory sample identification: D77657
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Hat Creek - Shaw Pit Facility

Material Information

Source Identification (SMARA or name of Pit): 91-25-0008::SHAW PIT
The fabricator's/manufacturer's product name for the sample: 18-1278.96-LAS
The fabricator/manufacturer designation for the sample: Unknown
The plant number: Unknown
A detailed description of where the material sample was collected: Cold Feed
Where the material sample would have been placed if not sampled: Unknown
Primary Aggregate Nominal Size: 3/4 inch
The concrete mix design number: JMF 18-18-S3
Lot number:
Sublot number:

Test Results

Test 1 of 1

DIME Test ID: 2018-09-22-6-1
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 10/10/2018
Date Tested: 09/24/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
What type of gradation is being tested? HMA Gradation
Does this test use 1/4 sieve? (question for HMA Gradation Type) Yes
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 99.1 %
Cumulative percent passing the 1/2 in. sieve 80.2 %
Cumulative percent passing the 3/8 in. sieve 67.4 %
Cumulative percent passing the 1/4 in. sieve 51.4 %
Cumulative percent passing the #4 sieve 44.7 %
Cumulative percent passing the #8 sieve 28.6 %
Cumulative percent passing the #16 sieve 18.3 %
Cumulative percent passing the #30 sieve 12.4 %
Cumulative percent passing the #50 sieve 9 %
Cumulative percent passing the #100 sieve 6.9 %
Cumulative percent passing the #200 sieve 5.37 %

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.