Print Report | Back to Sample Detail

Sample Record for 2018-05-15-33

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 212679 DEA: 023E7204 EFIS: 0200020154 QA Service Level: 1
DIST-CO-RTE-PM: 02-TEH-36-42.1/46.0
Work Description: COLD PLANING, PAVING, MINOR CONCRETE, ELECTRICAL AND STRIPING WORK.
Location Description: TEHAMA COUNTY IN AND NEAR RED BLUFF FROM EAST SAND SLOUGH BRIDGE TO 0.6 MILE EAST OF STICE ROAD
Contractor Name: TULLIS, INC.
Contractor Address: 16951 Clear Creek Rd., Redding, CA 96049
Resident Engineer: Anthony Granados Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2018-05-15-33
TL Number from the TL Form: 876217
Sample Submitted By Organization: CT D02 - North Region Materials Lab
Sample Organization Contact: (530) 225-3194
Type of Sample: Verification
Type of Material: Aggregate
Sample Taken Date: 05/15/2018
Date that the sample was received by the laboratory/organization performing the testing: 08/15/2018
The quantity of what the sample constitutes: JMF Verification
A brief description of the sample: 3/4-inch Type G Aggregate, Treated
From where was the sample collected: Manufacturer
Laboratory sample identification: D77388
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Tullis, Inc - Northstate Asphalt - Redding, CA

Material Information

Source Identification (SMARA or name of Pit): 91-45-0057::SHASTA RANCH AGGREGATES
The fabricator's/manufacturer's product name for the sample: 19-mm Type G Aggregate Treated
The fabricator/manufacturer designation for the sample: L180372
The plant number: Unknown
A detailed description of where the material sample was collected: Sampling device at plant
Where the material sample would have been placed if not sampled: Unknown
Primary Aggregate Nominal Size: 3/4 inch
The concrete mix design number: JMF 18-08-S1
Lot number:
Sublot number:

Test Results

Test 1 of 1

DIME Test ID: 2018-05-15-33-1
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 08/06/2018
Date Tested: 05/16/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Additional Comments When Verified:
What type of gradation is being tested? HMA Gradation
Does this test use 1/4 sieve? (question for HMA Gradation Type) Yes
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 99.8 %
Cumulative percent passing the 1/2 in. sieve 88.9 %
Cumulative percent passing the 3/8 in. sieve 68.3 %
Cumulative percent passing the 1/4 in. sieve 47.1 %
Cumulative percent passing the #4 sieve 36.1 %
Cumulative percent passing the #8 sieve 21.3 %
Cumulative percent passing the #16 sieve 14.6 %
Cumulative percent passing the #30 sieve 10.4 %
Cumulative percent passing the #50 sieve 7.8 %
Cumulative percent passing the #100 sieve 6.1 %
Cumulative percent passing the #200 sieve 4.88 %

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.