Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project ID: 213121 DEA: 09373504 EFIS: 0918000003
QA Service Level: 1
DIST-CO-RTE-PM: 09-MNO-395-93.7/106.3
Work Description: CONSTRUCT HOT MIX ASPHALT OVER COLD IN-PLACE RECYCLED PAVEMENT.
Location Description: MONO COUNTY NEAR WALKER FROM ROUTE 108 TO EASTSIDE LANE
Contractor Name: ROAD AND HIGHWAY BUILDERS OF CALIFORNIA, INC.
Contractor Address: P.O. BOX 70846, Reno, NV 89570
Resident Engineer: Lee Scotese Structure Rep.: Unknown
DIME Sample ID: 2018-07-30-4
TL Number from the TL Form: Unknown
Sample Submitted By Organization: CT D09 - Bishop Field Laboratory
Sample Organization Contact: (760) 872-5211
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 07/30/2018
Date that the sample was received by the laboratory/organization performing the testing: 07/31/2018
The quantity of what the sample constitutes: 6000 tons
A brief description of the sample: 3/4 inch hma PG64-28m
From where was the sample collected: Job Site
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Road and Highway Builders
DIME Test ID: 2018-07-30-4-1
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 04/03/2023
Date Tested: 08/03/2018
Submitted By Organization: CT D09 - Bishop Field Laboratory
Organization Address: 500 South Main Street,
Organization City: Bishop
Organization State: CA
Organization Zipcode: 93514
Organization Email: chris.talbot@dot.ca.gov
Organization Phone: (760) 872-0794
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids
|
3.7 %
|
Percent Air Voids 2
|
3.7
|
Percent Air Voids 3
|
3.9
|
Percent Air Voids Average
|
3.8
|
DIME Test ID: 2018-07-30-4-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 04/03/2023
Date Tested: 08/03/2018
Submitted By Organization: CT D09 - Bishop Field Laboratory
Organization Address: 500 South Main Street,
Organization City: Bishop
Organization State: CA
Organization Zipcode: 93514
Organization Email: chris.talbot@dot.ca.gov
Organization Phone: (760) 872-0794
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used?
|
Fahrenheit
|
Test procedure used?
|
Method A
|
Mass of HMA Sample prior to ignition
|
no data
|
Corrected Asphalt Binder Content
|
5.79 %
|
Mass Loss
|
no data
|
Correction Factor (Percent by mass of HMA Specimen)
|
no data
|
Moisture Content
|
no data
|
Temperature Compensation Factor
|
no data
|
Test Temperature
|
no data
|
DIME Test ID: 2018-07-30-4-4
Test Method: AASHTO T324-14: Standard Method of Test for Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures (Hamburg Wheel Track)
Verified Date: 04/03/2023
Date Tested: 08/03/2018
Submitted By Organization: CT D09 - Bishop Field Laboratory
Organization Address: 500 South Main Street,
Organization City: Bishop
Organization State: CA
Organization Zipcode: 93514
Organization Email: chris.talbot@dot.ca.gov
Organization Phone: (760) 872-0794
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel A)
|
no data
|
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel B)
|
no data
|
Impression at specified number of passes, or specified maximum impression if applicable (Wheel A)
|
no data
|
Impression at specified number of passes, or specified maximum impression if applicable (Wheel B)
|
no data
|
Stripping Inflection Point (Wheel A)
|
>25000
|
Stripping Inflection Point (Wheel B)
|
no data
|