Print Report | Back to Sample Detail

Sample Record for 2018-04-13-5

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 212948 DEA: 010F8604 EFIS: 0116000075 QA Service Level: 1
DIST-CO-RTE-PM: 01-HUM,DN-101-R131.7/R137.2,M0.0/M0.1
Work Description: RHMA, COLD PLANE AND HMA AT RAMPS, REPLACE GUARDRAIL WITH MGS
Location Description: HUMBOLDT AND DEL NORTE COUNTIES NEAR ORICK FROM 2.5 MILES NORTH OF BOYES CREEK VIADUCT TO NORTH PRAIRIE CREEK UNDERCROSSING
Contractor Name: TIDEWATER CONTRACTORS, INC
Contractor Address: P O BOX 1956, BROOKINGS, OR 97415
Resident Engineer: Clayton Malmberg Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2018-04-13-5
TL Number from the TL Form: 972601
Sample Submitted By Organization: CT D01 - District 1 Materials Laboratory
Sample Organization Contact: (707) 496-0974
Type of Sample: Verification
Type of Material: Hot Mix Asphalt
Sample Taken Date: 04/13/2018
Date that the sample was received by the laboratory/organization performing the testing: 04/16/2018
The quantity of what the sample constitutes: JMF Verification
A brief description of the sample: 1/2 HMA A W/15 RAP
From where was the sample collected: Manufacturer
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Tidewater Smith River

Material Information

HMA Type: Type A HMA
HMA Grading: 1/2 inch
Lot number:
Sublot number:
HMA Mix Number:
Test results on following page(s): 5

Test Results

Test 1 of 5

DIME Test ID: 2018-04-13-5-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 04/26/2018
Date Tested: 04/26/2018
Submitted By Organization: CT D01 - District 1 Materials Laboratory
Organization Address: 1726 Albee Street,
Organization City: Eureka
Organization State: CA
Organization Zipcode: 95501
Organization Email: leif.ayres@dot.ca.gov
Organization Phone: (707) 496-0974
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of HMA Sample prior to ignition no data
Corrected Asphalt Binder Content 7.90 %
Mass Loss no data
Correction Factor (Percent by mass of HMA Specimen) no data
Moisture Content no data
Temperature Compensation Factor no data
Test Temperature no data

Test 2 of 5

DIME Test ID: 2018-04-13-5-2
Test Method: AASHTO T329-13: Standard Method of Test for Moisture Content of Asphalt Mixtures by Oven Method (Moisture Content)
Verified Date: 04/26/2018
Date Tested: 04/26/2018
Submitted By Organization: CT D01 - District 1 Materials Laboratory
Organization Address: 1726 Albee Street,
Organization City: Eureka
Organization State: CA
Organization Zipcode: 95501
Organization Email: leif.ayres@dot.ca.gov
Organization Phone: (707) 496-0974
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Moisture Content 0.00 %
Percent Change 0 %

Test 3 of 5

DIME Test ID: 2018-04-13-5-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 04/26/2018
Date Tested: 04/26/2018
Submitted By Organization: CT D01 - District 1 Materials Laboratory
Organization Address: 1726 Albee Street,
Organization City: Eureka
Organization State: CA
Organization Zipcode: 95501
Organization Email: leif.ayres@dot.ca.gov
Organization Phone: (707) 496-0974
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Bulk Specific Gravity 2.458
Bulk Specific Gravity 2 2.453
Bulk Specific Gravity 3 2.456
Average Bulk Specific Gravity 2.456

Test 4 of 5

DIME Test ID: 2018-04-13-5-4
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 04/26/2018
Date Tested: 04/26/2018
Submitted By Organization: CT D01 - District 1 Materials Laboratory
Organization Address: 1726 Albee Street,
Organization City: Eureka
Organization State: CA
Organization Zipcode: 95501
Organization Email: leif.ayres@dot.ca.gov
Organization Phone: (707) 496-0974
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Specific Gravity for Sample 1 2.486
Theoretical maximum density at 25°C (77°F) no data

Test 5 of 5

DIME Test ID: 2018-04-13-5-5
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 04/26/2018
Date Tested: 04/26/2018
Submitted By Organization: CT D01 - District 1 Materials Laboratory
Organization Address: 1726 Albee Street,
Organization City: Eureka
Organization State: CA
Organization Zipcode: 95501
Organization Email: leif.ayres@dot.ca.gov
Organization Phone: (707) 496-0974
General Comments for this Test:
Test Result Compliance: does not comply
Additional Comments When Verified:
Percent Air Voids 1.1 %
Percent Air Voids 2 1.3
Percent Air Voids 3 1.2
Percent Air Voids Average 1.2