Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project ID: 212795 DEA: 05937704 EFIS: 0514901244 Permit Numbers: 05176UB0132
QA Service Level: 1
DIST-CO-RTE-PM: 05-MON-68-4.04
Work Description: Install a water pipeline bridge including a 36 inch diameter steel casing
Location Description: County of Monterey
Contractor Name: Garney Construction Company
Contractor Address: 1110 Airport Rd, Monterey, CA 93940
Resident Engineer: Ignacio Saavedra Structure Rep.: David Galarza
DIME Sample ID: 2018-04-12-5
TL Number from the TL Form: C740748
Sample Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Sample Organization Contact: (530) 329-6527
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 04/12/2018
Date that the sample was received by the laboratory/organization performing the testing: 04/17/2018
The quantity of what the sample constitutes: 4
A brief description of the sample: A449 Threaded rod
From where was the sample collected: Manufacturer
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Portland Bolt
Rocap Number(s):
Heat Number(s): A175837, B46227, 6214434108
Nut Mfg. Lot Number(s): 26728-6214434108
Washer Mfg. Lot Number(s): 0218-749
Bolt Specification: A449
Bolt Length(s): Unknown
Nut Specification: A563
Washer Specification: F436-1
Finish: HDG
Diameter/Size: 1-1/4"
Bolt Mfg. Lot Number:
Rocap Test Requirement(s):
Lubricant Requirements(s):
DIME Test ID: 2018-04-12-5-2
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 04/24/2018
Date Tested: 04/18/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A449 Rod & Nut
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments | 1A | A449 1.250 x 60.5\" Althread Rod w / Nut | 0.969 | 132674 | 590 | 136919 | 123265 | 119444 | A449 Rod & Nut |
| |
UTM
|
400KIP
|
Temperature
|
72
|
DIME Test ID: 2018-04-12-5-3
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 04/24/2018
Date Tested: 04/18/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
A175837
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
A449
|
Size
|
1.250 in
|
Bolt Length
|
60.5 in
|
Gage Type
|
Pass
|
DIME Test ID: 2018-04-12-5-4
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 04/24/2018
Date Tested: 04/18/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
26728-6214434108
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
U DH
|
Size
|
1.250 in
|
Gage Type
|
Pass
|
DIME Test ID: 2018-04-12-5-5
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 04/24/2018
Date Tested: 04/18/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
A175837
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
A449
|
Size
|
1.250 in
|
Bolt Length
|
60.5 in
|
Measurement Average
|
4.91 mils
|
DIME Test ID: 2018-04-12-5-6
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 04/24/2018
Date Tested: 04/18/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
26728-6214434108
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
U DH
|
Size
|
1.250 in
|
Bolt Length
|
no data in
|
Measurement Average
|
4.85 mils
|
DIME Test ID: 2018-04-12-5-7
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 04/24/2018
Date Tested: 04/18/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
0218-749
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
TSI
|
Size
|
1.250 in
|
Bolt Length
|
no data in
|
Measurement Average
|
3.64 mils
|
DIME Test ID: 2018-04-12-5-8
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 04/24/2018
Date Tested: 04/18/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
0218-749
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
TSI
|
Size
|
1.250 in
|
Bolt Length
|
no data in
|
Hardness Reading Scale
|
C Scale
|
Hardness Reading Average
|
38.8
|
Spacing
|
Ok
|