Print Report | Back to Sample Detail

Sample Record for 2018-04-02-6

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 212886 DEA: 023H1204 QA Service Level: 1
DIST-CO-RTE-PM: 02-TEH-5-R0.0/R22.4
Work Description: COLD PLANE RAC-O, PLACE RHMA-O, REPLACE AC SURFACING, MBGR
Location Description: TEHAMA COUNTY AT AND NEAR CORNING FROM GLENN COUNTY LINE TO 0.3 MILE NORTH OF BRANCH COYOTE CREEK BRIDGE
Contractor Name: TULLIS INC
Contractor Address: P O BOX 493416, REDDING CA 96049
Resident Engineer: Henry Benner Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2018-04-02-6
TL Number from the TL Form: 852090
Sample Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Sample Organization Contact: (530) 225-3194
Type of Sample: Department Acceptance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 04/02/2018
Date that the sample was received by the laboratory/organization performing the testing: 04/03/2018
The quantity of what the sample constitutes: Production Start Up Evaluation
A brief description of the sample: 3/4-inch Type A HMA
From where was the sample collected: Manufacturer
Laboratory sample identification: 17-07-P07, D77310
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Tullis Inc - Northstate Asphalt - Redding, CA

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number:
Sublot number:
HMA Mix Number:
Test results on following page(s): 6

Test Results

Test 1 of 6

DIME Test ID: 2018-04-02-6-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 04/09/2018
Date Tested: 04/03/2018
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of HMA Sample prior to ignition no data
Corrected Asphalt Binder Content 4.60 %
Mass Loss no data
Correction Factor (Percent by mass of HMA Specimen) no data
Moisture Content no data
Temperature Compensation Factor no data
Test Temperature no data

Test 2 of 6

DIME Test ID: 2018-04-02-6-2
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 04/09/2018
Date Tested: 04/03/2018
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Air
Method Performed no data
Mass of container filled with water 7374.0 grams
Mass of oven-dry sample in air for Sample 1 2569.0 grams
Mass of container filled with the sample and water for Sample 1 8913.0 grams
Temperature of Water 77 °F
Specific Gravity for Sample 1 2.492
Theoretical maximum density at 25°C (77°F) no data

Test 3 of 6

DIME Test ID: 2018-04-02-6-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 04/09/2018
Date Tested: 04/03/2018
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Bulk Specific Gravity 2.415
Bulk Specific Gravity 2 2.417
Bulk Specific Gravity 3 2.422
Average Bulk Specific Gravity 2.418

Test 4 of 6

DIME Test ID: 2018-04-02-6-4
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 04/09/2018
Date Tested: 04/03/2018
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 3.1 %
Percent Air Voids 2 3.0
Percent Air Voids 3 2.8
Percent Air Voids Average 3.0

Test 5 of 6

DIME Test ID: 2018-04-02-6-6
Test Method: AASHTO T324-14: Standard Method of Test for Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures (Hamburg Wheel Track)
Verified Date: 04/11/2018
Date Tested: 04/06/2018
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel A) no data
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel B) no data
Impression at specified number of passes, or specified maximum impression if applicable (Wheel A) no data
Impression at specified number of passes, or specified maximum impression if applicable (Wheel B) no data
Stripping Inflection Point (Wheel A) >25000
Stripping Inflection Point (Wheel B) no data

Test 6 of 6

DIME Test ID: 2018-04-02-6-7
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 04/11/2018
Date Tested: 04/10/2018
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 167 psi
Average Wet Tensile Strength 157 psi
Tensile Strength Ratio 0.94