Print Report | Back to Sample Detail

Sample Record for 2018-04-06-5

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

DEA: No Project QA Service Level:
DIST-CO-RTE-PM: ---
Work Description: Special project identifier for material not associated with a project
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2018-04-06-5
TL Number from the TL Form: Unknown
Sample Submitted By Organization: CT HQ - QASI Sacramento Field Office
Sample Organization Contact: (916) 2058871
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 04/06/2018
Date that the sample was received by the laboratory/organization performing the testing: 04/12/2018
The quantity of what the sample constitutes: 1
A brief description of the sample: F1554 Anchor Rods Nuts Washers
From where was the sample collected: Source
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: A and M Nut and Bolt

Material Information

Rocap Number(s):
Heat Number(s): 3071635
Nut Mfg. Lot Number(s): W4493
Washer Mfg. Lot Number(s):
Bolt Specification: F1554 Gr. 55
Bolt Length(s): 60"
Nut Specification: A193 Gr. 2H/ A563 Gr. DH
Washer Specification: F436 S Mark HDG
Finish:
Diameter/Size: 3"
Bolt Mfg. Lot Number: 41923-PPO
Rocap Test Requirement(s):
Lubricant Requirements(s):
Test results on following page(s): 12

Test Results

Test 1 of 12

DIME Test ID: 2018-04-06-5-1
Test Method: ASTM A370-15: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleHeat NumberDiameter (in)Area (sqin)Stress at Offset (psi)Tensile Strength (psi)Elongation in 4 x d (%)Tested By
130716350.4990.196707229698025.1Fred
UTM 67KIP
Temperature 72 f

Test 2 of 12

DIME Test ID: 2018-04-06-5-2
Test Method: ASTM A370-15: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleHeat NumberDiameter (in)Area (sqin)Stress at Offset (psi)Tensile Strength (psi)Elongation in 4 x d (%)Tested By
230716350.4990.196717879729024.4Fred
UTM 67KIP
Temperature 72 f

Test 3 of 12

DIME Test ID: 2018-04-06-5-3
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) 3071635
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings YELLOW PAINT
Size 3 in
Bolt Length 60 in
Gage Type Pass

Test 4 of 12

DIME Test ID: 2018-04-06-5-4
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number W42193
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H DH LSE
Size 3 in
Gage Type Pass

Test 5 of 12

DIME Test ID: 2018-04-06-5-5
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number W42193
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H DH LSE
Size 3 in
Gage Type Pass

Test 6 of 12

DIME Test ID: 2018-04-06-5-6
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) 3071635
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings YELLOW PAINT
Size 3 in
Bolt Length 60 in
Measurement Average 5.64 mils

Test 7 of 12

DIME Test ID: 2018-04-06-5-7
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number W42193
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H DH LSE
Size 3 in
Bolt Length no data in
Measurement Average 4.89 mils

Test 8 of 12

DIME Test ID: 2018-04-06-5-8
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number W42193
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H DH LSE
Size 3 in
Bolt Length no data in
Measurement Average 5.38 mils

Test 9 of 12

DIME Test ID: 2018-04-06-5-9
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 295518
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size 3 in
Bolt Length no data in
Measurement Average 3.37 mils

Test 10 of 12

DIME Test ID: 2018-04-06-5-10
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 295518
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size 3 in
Bolt Length no data in
Measurement Average 3.01 mils

Test 11 of 12

DIME Test ID: 2018-04-06-5-11
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number W4493
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H DH LSE
Size 3 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 25.1
Spacing Ok

Test 12 of 12

DIME Test ID: 2018-04-06-5-12
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 04/19/2018
Date Tested: 04/17/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number W4493
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H DH LSE
Size 3 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 23.88
Spacing Ok