Print Report | Back to Sample Detail

Sample Record for 2018-02-27-18

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 212679 DEA: 023E7204 EFIS: 0200020154 QA Service Level: 1
DIST-CO-RTE-PM: 02-TEH-36-42.1/46.0
Work Description: COLD PLANING, PAVING, MINOR CONCRETE, ELECTRICAL AND STRIPING WORK.
Location Description: TEHAMA COUNTY IN AND NEAR RED BLUFF FROM EAST SAND SLOUGH BRIDGE TO 0.6 MILE EAST OF STICE ROAD
Contractor Name: TULLIS, INC.
Contractor Address: 16951 Clear Creek Rd., Redding, CA 96049
Resident Engineer: Anthony Granados Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2018-02-27-18
TL Number from the TL Form: 852088
Sample Submitted By Organization: CT D02 - North Region Materials Lab
Sample Organization Contact: (530) 225-3194
Type of Sample: Verification
Type of Material: Aggregate
Sample Taken Date: 02/27/2018
Date that the sample was received by the laboratory/organization performing the testing: 02/27/2018
The quantity of what the sample constitutes: JMF
A brief description of the sample: Virgin 1/2-inch Type A Untreated
From where was the sample collected: Manufacturer
Laboratory sample identification: D77292F
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Tullis, Inc - Northstate Asphalt - Redding, CA

Material Information

Source Identification (SMARA or name of Pit): 91-45-0057::SHASTA RANCH AGGREGATES
The fabricator's/manufacturer's product name for the sample: Unknown
The fabricator/manufacturer designation for the sample: Unknown
The plant number: Unknown
A detailed description of where the material sample was collected: Lab-batched from untreated stockpiles
Where the material sample would have been placed if not sampled: Unknown
Primary Aggregate Nominal Size: 1/2 inch
The concrete mix design number: Unknown
Lot number:
Sublot number:

Test Results

Test 1 of 10

DIME Test ID: 2018-02-27-18-1
Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)
Verified Date: 03/27/2018
Date Tested: 03/02/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
What type of gradation is being tested? HMA Gradation
Does this test use 1/4 sieve? (question for HMA Gradation Type) Yes
Cumulative percent passing the 1 1/2 in. sieve 100 %
Cumulative percent passing the 1 in. sieve 100 %
Cumulative percent passing the 3/4 in. sieve 100 %
Cumulative percent passing the 1/2 in. sieve 95.6 %
Cumulative percent passing the 3/8 in. sieve 83.9 %
Cumulative percent passing the 1/4 in. sieve 64.8 %
Cumulative percent passing the #4 sieve 55.7 %
Cumulative percent passing the #8 sieve 36.4 %
Cumulative percent passing the #16 sieve 24.1 %
Cumulative percent passing the #30 sieve 16.4 %
Cumulative percent passing the #50 sieve 11.4 %
Cumulative percent passing the #100 sieve 8.1 %
Cumulative percent passing the #200 sieve 6 %

Test 2 of 10

DIME Test ID: 2018-02-27-18-2
Test Method: CTM 204-June 2010: Method of Test for Liquid Limit, Plastic Limit and Plasticity Index of Soils (Plasticity Index)
Verified Date: 03/27/2018
Date Tested: 03/05/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Plastic Index(PI) NP
Liquid Limit (LL) 0 %
Plastic Limit (PL) 0 %

Test 3 of 10

DIME Test ID: 2018-02-27-18-3
Test Method: AASHTO T335-09r13: Standard Method of Test for Determining the Percentage of Fracture in Coarse Aggregate (Percent of Crushed Particles)
Verified Date: 03/27/2018
Date Tested: 03/05/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Method 1 - Combined Fracture Determination
Aggregate Size and Fracture Type Coarse 1 and 2 Faced and Fine 1 Faced
Percentage of questionable, coarse, 2 faced particles tested 1 %
Percentage of questionable, coarse, 1 faced particles tested 1 %
Percentage of questionable, fine, 1 faced particles tested 1 %
Percentage of fractured, coarse, 2 faced particles tested 99 %
Percentage of fractured, coarse, 1 faced particles tested 100 %
Percentage of fractured, fine, 1 faced particles tested 100 %

Test 4 of 10

DIME Test ID: 2018-02-27-18-4
Test Method: AASHTO T85-13: Standard Method of Test for Specific Gravity and Absorption of Coarse Aggregate (Coarse Specific Gravity)
Verified Date: 03/27/2018
Date Tested: 03/07/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Basis for relative density testing Bulk
Specific Gravity 2.645
Absorption 1.4 %

Test 5 of 10

DIME Test ID: 2018-02-27-18-5
Test Method: AASHTO T84-14: Standard Method of Test for Specific Gravity and Absorption of Fine Aggregate (Fine Specific Gravity)
Verified Date: 03/27/2018
Date Tested: 03/08/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Bulk specific gravity 2.640
Bulk specific gravity (SSD Basis) 2.680
Apparent specific gravity 2.750
Absorption 1.5 %

Test 6 of 10

DIME Test ID: 2018-02-27-18-6
Test Method: AASHTO T96-02r10: Standard Method of Test for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine (Los Angeles Rattler)
Verified Date: 03/27/2018
Date Tested: 03/02/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Grading designation C
Mass of sample on No.12 sieve (after 500 revolutions) 4160 grams
Percent loss after 100 revolutions 4 %
Percent loss after 500 revolutions 16 %

Test 7 of 10

DIME Test ID: 2018-02-27-18-8
Test Method: AASHTO T176-08: Standard Method of Test for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test (Sand Equivalent)
Verified Date: 03/27/2018
Date Tested: 03/02/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Sand Equivalent 68

Test 8 of 10

DIME Test ID: 2018-02-27-18-9
Test Method: AASHTO T210-15: Standard Method of Test for Aggregate Durability Index (Durability Index)
Verified Date: 03/27/2018
Date Tested: 03/02/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Which test procedure(s) is/are used? Procedure A and Procedure B
Was strict temperature control maintained? Yes
What type of water was used? Distilled
Durability Index (coarse) 87
Durability Index (fine) 83

Test 9 of 10

DIME Test ID: 2018-02-27-18-10
Test Method: AASHTO T304-11: Standard Method of Test for Uncompacted Void Content of Fine Aggregate (Fine of Crushed Particles)
Verified Date: 03/27/2018
Date Tested: 03/05/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What test method is performed? Method A
Bulk dry specific gravity 2.64
Average uncompacted voids 47.9 %

Test 10 of 10

DIME Test ID: 2018-02-27-18-11
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Verified Date: 03/27/2018
Date Tested: 03/05/2018
Submitted By Organization: CT D02 - North Region Materials Lab
Organization Address: 1657 Riverside Dr,MS-83
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: (530) 225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Method B
Determination By Mass
Dimensional ratio used 1:5
Weighted percentage of particles (by mass) that were flat and elongated 0 %
Weighted percentage of particles (by mass) that were not flat and elongated 100 %

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
2018-02-27-18-7AASHTO T104-99r16: Standard Method of Test for Soundness of Aggregate by Use of Sodium Sulfate or Magnesium Sulfate (Soundness)03/27/2018Not scheduledWard JenkinsCT HQ - Sacramento Aggregate Testing Laboratory