Print Report | Back to Sample Detail

Sample Record for 2018-02-16-4

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

DEA: No Project QA Service Level:
DIST-CO-RTE-PM: ---
Work Description: Special project identifier for material not associated with a project
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2018-02-16-4
TL Number from the TL Form:
Sample Submitted By Organization: CT - Unassigned/General Field Laboratory
Sample Organization Contact: 5625005861
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 02/16/2018
Date that the sample was received by the laboratory/organization performing the testing: 02/23/2018
The quantity of what the sample constitutes: 48
A brief description of the sample: Anchor Bolt Assembly
From where was the sample collected: Source
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: AM Nut and Bolt

Material Information

Rocap Number(s):
Heat Number(s): 3075024, 177736, 162495
Nut Mfg. Lot Number(s): DDYD
Washer Mfg. Lot Number(s): 302113
Bolt Specification: F1554
Bolt Length(s): 42"
Nut Specification: A194
Washer Specification: F436
Finish: HDG
Diameter/Size: 1 1/2"
Bolt Mfg. Lot Number: 3075024
Rocap Test Requirement(s):
Lubricant Requirements(s):
Test results on following page(s): 15

Test Results

Test 1 of 15

DIME Test ID: 2018-02-16-4-1
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 03/01/2018
Date Tested: 02/27/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test: Nut Proof
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)CommentsTested By
4ADDYD1 1/2\"213660950.41Nut ProofBrian
UTM 400KIP
Temperature 72 F

Test 2 of 15

DIME Test ID: 2018-02-16-4-2
Test Method: ASTM A370-15: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Verified Date: 03/01/2018
Date Tested: 02/28/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleHeat NumberDiameter (in)Area (sqin)Stress at Offset (psi)Tensile Strength (psi)Elongation in 4 x d (%)Tested By
130750240.5010.197644079148026.7Brian
UTM 67KIP
Temperature 72 f

Test 3 of 15

DIME Test ID: 2018-02-16-4-3
Test Method: ASTM A370-15: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Verified Date: 03/01/2018
Date Tested: 02/28/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleHeat NumberDiameter (in)Area (sqin)Stress at Offset (psi)Tensile Strength (psi)Elongation in 4 x d (%)Tested By
230750240.5010.197646539154026.6Brian
UTM 67KIP
Temperature 72 f

Test 4 of 15

DIME Test ID: 2018-02-16-4-4
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) 3075024
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings YELLOW PAINT
Size 1.5 in
Bolt Length 42 in
Gage Type Pass

Test 5 of 15

DIME Test ID: 2018-02-16-4-5
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number DDYD
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H/DH D/N
Size 1.5 in
Gage Type Pass

Test 6 of 15

DIME Test ID: 2018-02-16-4-6
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number DDYD
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H/DH D/N
Size 1.5 in
Gage Type Pass

Test 7 of 15

DIME Test ID: 2018-02-16-4-7
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number DDYD
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H/DH D/N
Size 1.5 in
Gage Type Pass

Test 8 of 15

DIME Test ID: 2018-02-16-4-8
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) 3075024
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings YELLOW PAINT
Size 1.5 in
Bolt Length 42 in
Measurement Average 5.63 mils

Test 9 of 15

DIME Test ID: 2018-02-16-4-9
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number DDYD
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H/DH D/N
Size 1.5 in
Bolt Length no data in
Measurement Average 4.01 mils

Test 10 of 15

DIME Test ID: 2018-02-16-4-10
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number DDYD
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H/DH D/N
Size 1.5 in
Bolt Length no data in
Measurement Average 4.79 mils

Test 11 of 15

DIME Test ID: 2018-02-16-4-11
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number DDYD
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H/DH D/N
Size 1.5 in
Bolt Length no data in
Measurement Average 3.21 mils

Test 12 of 15

DIME Test ID: 2018-02-16-4-12
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 302113
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size 1.5 in
Bolt Length no data in
Measurement Average 3.59 mils

Test 13 of 15

DIME Test ID: 2018-02-16-4-13
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 302113
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size 1.5 in
Bolt Length no data in
Measurement Average 3.18 mils

Test 14 of 15

DIME Test ID: 2018-02-16-4-14
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 302113
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size 1.5 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 34.75
Spacing Ok

Test 15 of 15

DIME Test ID: 2018-02-16-4-15
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 03/01/2018
Date Tested: 03/01/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: 916-227-7257
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 302113
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size 1.5 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 35.25
Spacing Ok