Print Report | Back to Sample Detail

Sample Record for 2018-01-11-2

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 211669 DEA: 022C0904 EFIS: 0200000161 QA Service Level: 1
DIST-CO-RTE-PM: 02-PLU-70-50.6/51.7
Work Description: BRIDGE WIDENING AND DECK REPLACEMENT, HMA, MGS AND CULVERT REPLACEMENT
Location Description: PLUMAS COUNTY NEAR QUINCY FROM 0.6 MILE WEST TO 0.5 MILE EAST OF SPRING GARDEN BRIDGE OVERHEAD
Contractor Name: MCM Construction
Contractor Address: 6413 32ND STREET, North Highlands, Ca 95660
Resident Engineer: Ronald Collins Structure Rep.: Jeffrey Rothgery

Sample Information

DIME Sample ID: 2018-01-11-2
TL Number from the TL Form: Unknown
Sample Submitted By Organization: CT HQ - QASI Sacramento Field Office
Sample Organization Contact: (916) 2058871
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 01/11/2018
Date that the sample was received by the laboratory/organization performing the testing: 01/11/2018
The quantity of what the sample constitutes: 206
A brief description of the sample: A449 All thread
From where was the sample collected: Distributor
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: UIS

Material Information

Rocap Number(s): N/A
Heat Number(s): DL15105873
Nut Mfg. Lot Number(s): N/A
Washer Mfg. Lot Number(s): N/A
Bolt Specification: A449
Bolt Length(s): 16"
Nut Specification: N/A
Washer Specification: N/A
Finish: HDG
Diameter/Size: 3/4
Bolt Mfg. Lot Number: 29330
Rocap Test Requirement(s): No
Lubricant Requirements(s): No
Test results on following page(s): 7

Test Results

Test 1 of 7

DIME Test ID: 2018-01-11-2-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 01/22/2018
Date Tested: 01/22/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: 449 Althread Stud
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleSizeArea (in^2)Peak Load (lbf)Peak Load (kN)Tensile Strength (psi)Stress at Offset (psi)Load at Offset (lbf)Comments
1AA449 .75 x 16 Althreaded Stud0.3344386019513131711605938764449 Althread Stud
UTM 400KIP
Temperature 72

Test 2 of 7

DIME Test ID: 2018-01-11-2-2
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/22/2018
Date Tested: 01/22/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) DL15105873
Mfg. Lot Number 29330
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size .75 in
Bolt Length 16 in
Gage Type Pass

Test 3 of 7

DIME Test ID: 2018-01-11-2-3
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/22/2018
Date Tested: 01/22/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) DL15105873
Mfg. Lot Number 29330
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size .75 in
Bolt Length 16 in
Gage Type Pass

Test 4 of 7

DIME Test ID: 2018-01-11-2-4
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/22/2018
Date Tested: 01/22/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) DL15105873
Mfg. Lot Number 29330
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size .75 in
Bolt Length 16 in
Gage Type Pass

Test 5 of 7

DIME Test ID: 2018-01-11-2-5
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/22/2018
Date Tested: 01/22/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) DL15105873
Mfg. Lot Number 29330
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size .75 in
Bolt Length 16 in
Measurement Average 9.98 mils

Test 6 of 7

DIME Test ID: 2018-01-11-2-6
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/22/2018
Date Tested: 01/22/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) DL15105873
Mfg. Lot Number 29330
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size .75 in
Bolt Length 16 in
Measurement Average 8.96 mils

Test 7 of 7

DIME Test ID: 2018-01-11-2-7
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/22/2018
Date Tested: 01/22/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) DL15105873
Mfg. Lot Number 29330
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size .75 in
Bolt Length 16 in
Measurement Average 7.5 mils