Print Report | Back to Sample Detail

Sample Record for 2017-12-14-4

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 212312 DEA: 100X9104 EFIS: 1013000041 QA Service Level: 1
DIST-CO-RTE-PM: 10-SJ,TUO,STA-4,120,132-Var
Work Description: MITIGATING SCOUR, PLACING ROCK SLOPE PROTECTION,AND REPAIRING
Location Description: SAN JOAQUIN,STANISLAUS, AND TUOLUMNE COUNTIES AT VARIOUS LOCATIONS.
Contractor Name: Dreambuilder Construction Corporation
Contractor Address: 1324 E LAWSON LANE, PLACENTIA CA 92870
Resident Engineer: Quan Trinh Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2017-12-14-4
TL Number from the TL Form:
Sample Submitted By Organization: CT - Unassigned/General Field Laboratory
Sample Organization Contact: 5625005861
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 12/14/2017
Date that the sample was received by the laboratory/organization performing the testing: 12/14/2017
The quantity of what the sample constitutes: 27
A brief description of the sample: Threaded Bar
From where was the sample collected: Distributor
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Portland Bolt

Material Information

Rocap Number(s):
Heat Number(s): 073417
Nut Mfg. Lot Number(s): 17-40-005
Washer Mfg. Lot Number(s):
Bolt Specification: A563 Grade A
Bolt Length(s): 42"
Nut Specification: 36
Washer Specification: NA
Finish: F2329 / A153
Diameter/Size: .750
Bolt Mfg. Lot Number:
Rocap Test Requirement(s):
Lubricant Requirements(s):

Test Results

Test 1 of 9

DIME Test ID: 2017-12-14-4-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 12/14/2017
Date Tested: 12/14/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test: A307A Stud & Nut Proof
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleSizeArea (in^2)Peak Load (lbf)Peak Load (kN)Tensile Strength (psi)Stress at Offset (psi)Load at Offset (lbf)Comments
1AA307A 3/4!\" x 42 Stud 0.33428839128863446011920080A307A Stud & Nut Proof
UTM 400KIP
Temperature 72

Test 2 of 9

DIME Test ID: 2017-12-14-4-2
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 12/14/2017
Date Tested: 12/14/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 073417
Mfg. Lot Number no data
Finish Coating Plain and ASTM F2329 - Hot Dip
Product Markings no data
Size .750 in
Bolt Length 42 in
Gage Type Pass

Test 3 of 9

DIME Test ID: 2017-12-14-4-3
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 12/14/2017
Date Tested: 12/14/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 17-40-005
Finish Coating ASTM F2329 - Hot Dip
Product Markings no data
Size .750 in
Gage Type Pass

Test 4 of 9

DIME Test ID: 2017-12-14-4-4
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 12/14/2017
Date Tested: 12/14/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 17-40-005
Finish Coating ASTM F2329 - Hot Dip
Product Markings no data
Size .750 in
Gage Type Pass

Test 5 of 9

DIME Test ID: 2017-12-14-4-5
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 12/14/2017
Date Tested: 12/14/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 17-40-005
Finish Coating ASTM F2329 - Hot Dip
Product Markings no data
Size .750 in
Gage Type Pass

Test 6 of 9

DIME Test ID: 2017-12-14-4-6
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/14/2017
Date Tested: 12/14/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 073417
Mfg. Lot Number no data
Finish Coating Plain and ASTM F2329 - Hot Dip
Product Markings no data
Size .750 in
Bolt Length 42 in
Measurement Average 4.5 mils

Test 7 of 9

DIME Test ID: 2017-12-14-4-7
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/14/2017
Date Tested: 12/14/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 17-40-005
Finish Coating ASTM F2329 - Hot Dip
Product Markings no data
Size .750 in
Bolt Length no data in
Measurement Average 3.21 mils

Test 8 of 9

DIME Test ID: 2017-12-14-4-8
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/14/2017
Date Tested: 12/14/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 17-40-005
Finish Coating ASTM F2329 - Hot Dip
Product Markings no data
Size .750 in
Bolt Length no data in
Measurement Average 3.1 mils

Test 9 of 9

DIME Test ID: 2017-12-14-4-9
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/14/2017
Date Tested: 12/14/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 17-40-005
Finish Coating ASTM F2329 - Hot Dip
Product Markings no data
Size .750 in
Bolt Length no data in
Measurement Average 3.51 mils

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.