Print Report | Back to Sample Detail

Sample Record for 2017-10-31-5

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 88888 DEA: SMTL-STOCK EFIS: SMTL-STOCK QA Service Level:
DIST-CO-RTE-PM: 59---
Work Description: Special project for SMTL stock material. Object Code: 1025. J2 DEA: 912680.
Location Description:
Contractor Name: Unknown
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2017-10-31-5
TL Number from the TL Form: Unknown
Sample Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Sample Organization Contact: (530) 329-6527
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 10/31/2017
Date that the sample was received by the laboratory/organization performing the testing: 11/02/2017
The quantity of what the sample constitutes: 3
A brief description of the sample: 3/4 fastener assembly
From where was the sample collected: Manufacturer
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Hodell-Natco Nucor

Material Information

Rocap Number(s): 503104
Heat Number(s): 10493530, DL16104127, A46920
Nut Mfg. Lot Number(s): 382492B
Washer Mfg. Lot Number(s): 0316-187
Bolt Specification: A325 A449
Bolt Length(s): 8"
Nut Specification: A563
Washer Specification: F436
Finish: HDG
Diameter/Size: 3/4"
Bolt Mfg. Lot Number: J32891
Rocap Test Requirement(s):
Lubricant Requirements(s):

Test Results

Test 1 of 8

DIME Test ID: 2017-10-31-5-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 11/06/2017
Date Tested: 11/03/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A449 / A325 Headed Bolt 10 DEG Weage
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleSizeArea (in^2)Peak Load (lbf)Peak Load (kN)Tensile Strength (psi)Stress at Offset (psi)Load at Offset (lbf)Comments
1AA449 .75\" x 8 Bolt 10 Deg Wedge0.3344741021014194613612045464A449 / A325 Headed Bolt 10 DEG Weage
UTM 400KIP
Temperature 72

Test 2 of 8

DIME Test ID: 2017-10-31-5-2
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 11/06/2017
Date Tested: 11/03/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof Load
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)CommentsTested By
1A764901?\"50669225.39Nut Proof LoadFred
UTM 400KIP
Temperature 72 F

Test 3 of 8

DIME Test ID: 2017-10-31-5-7
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 11/06/2017
Date Tested: 11/03/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) J32891
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 SL USA
Size .75 in
Bolt Length 8 in
Gage Type Pass

Test 4 of 8

DIME Test ID: 2017-10-31-5-8
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 11/06/2017
Date Tested: 11/03/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 764901
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size .75 in
Gage Type Pass

Test 5 of 8

DIME Test ID: 2017-10-31-5-9
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/06/2017
Date Tested: 11/03/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) J32891
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325 SL USA
Size .75 in
Bolt Length 8 in
Measurement Average 2.41 mils

Test 6 of 8

DIME Test ID: 2017-10-31-5-10
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/06/2017
Date Tested: 11/03/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 764901
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size .75 in
Bolt Length no data in
Measurement Average 2.82 mils

Test 7 of 8

DIME Test ID: 2017-10-31-5-11
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/06/2017
Date Tested: 11/03/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 0316-187
Finish Coating ASTM F2329 - Hot Dip
Product Markings TSI F436
Size .75 in
Bolt Length no data in
Measurement Average 5.38 mils

Test 8 of 8

DIME Test ID: 2017-10-31-5-12
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 11/06/2017
Date Tested: 11/03/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 0316-187
Finish Coating ASTM F2329 - Hot Dip
Product Markings TSI F436
Size .75 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 39.7
Spacing Ok

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
2017-10-31-5-3ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)11/03/201711/03/2017Fred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor
2017-10-31-5-4ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)11/03/201711/03/2017Fred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor
2017-10-31-5-5ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)11/03/201711/03/2017Fred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor
2017-10-31-5-6ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)11/03/201711/03/2017Fred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor