Print Report | Back to Sample Detail

Sample Record for 2017-10-31-1

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 211796 DEA: 073X8704 EFIS: 0713000241 QA Service Level: 1
DIST-CO-RTE-PM: 07-LA-105,405-R2.5,20.5/R21.1
Work Description: SLOPE RECONSTRUCTION AND PAVEMENT REPAIR
Location Description: LOS ANGELES COUNTY IN AND NEAR HAWTHORNE FROM EL SEGUNDO BOULEVARD UNDERCROSSING TO ROUTE 105/405 SEPARATION
Contractor Name: GRIFFITH COMPANY
Contractor Address: 12200 BLOOMFIELD AVENUE, SANTA FE SPRINGS, CA 90670
Resident Engineer: Mashhur Ali Structure Rep.: Frank Lotfi

Sample Information

DIME Sample ID: 2017-10-31-1
TL Number from the TL Form: Unknown
Sample Submitted By Organization: CT - Unassigned/General Field Laboratory
Sample Organization Contact: 5625005861
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 10/31/2017
Date that the sample was received by the laboratory/organization performing the testing: 10/31/2017
The quantity of what the sample constitutes: 3
A brief description of the sample: F1554 Gr. 55
From where was the sample collected: Fabricator
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Structural and Steel Products

Material Information

Rocap Number(s):
Heat Number(s): 3074489
Nut Mfg. Lot Number(s): DDBR Galvanized / W1381 Plain
Washer Mfg. Lot Number(s): 302919
Bolt Specification: F1554 Gr 55
Bolt Length(s): 50"
Nut Specification: A563
Washer Specification: F436
Finish: Galvanized / Plain
Diameter/Size: 2"
Bolt Mfg. Lot Number:
Rocap Test Requirement(s):
Lubricant Requirements(s):
Test results on following page(s): 11

Test Results

Test 1 of 11

DIME Test ID: 2017-10-31-1-1
Test Method: ASTM A370-15: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Verified Date: 11/09/2017
Date Tested: 11/08/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleHeat NumberDiameter (in)Area (sqin)Stress at Offset (psi)Tensile Strength (psi)Elongation in 4 x d (%)Tested By
130744890.5040.2702869637025.8Fred
UTM 67KIP
Temperature 72 f

Test 2 of 11

DIME Test ID: 2017-10-31-1-2
Test Method: ASTM A370-15: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Verified Date: 11/09/2017
Date Tested: 11/08/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleHeat NumberDiameter (in)Area (sqin)Stress at Offset (psi)Tensile Strength (psi)Elongation in 4 x d (%)Tested By
230744890.5050.2698849618025.8Fred
UTM 67KIP
Temperature 72 f

Test 3 of 11

DIME Test ID: 2017-10-31-1-7
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 11/09/2017
Date Tested: 11/08/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 3074489
Mfg. Lot Number no data
Finish Coating Plain and A153 and F2329
Product Markings YELLOW PAINT
Size 2 in
Bolt Length 50 in
Gage Type Pass

Test 4 of 11

DIME Test ID: 2017-10-31-1-8
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 11/09/2017
Date Tested: 11/08/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number DDBR
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H / DH
Size 2 in
Gage Type Pass

Test 5 of 11

DIME Test ID: 2017-10-31-1-9
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 11/09/2017
Date Tested: 11/08/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number W1381
Finish Coating Plain
Product Markings 2H / DH
Size 2 in
Gage Type Pass

Test 6 of 11

DIME Test ID: 2017-10-31-1-10
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/09/2017
Date Tested: 11/08/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 3074489
Mfg. Lot Number no data
Finish Coating Plain and A153 and F2329
Product Markings YELLOW PAINT
Size 2 in
Bolt Length 50 in
Measurement Average 6.82 mils

Test 7 of 11

DIME Test ID: 2017-10-31-1-11
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/09/2017
Date Tested: 11/08/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number DDBR
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H / DH
Size 2 in
Bolt Length no data in
Measurement Average 8.31 mils

Test 8 of 11

DIME Test ID: 2017-10-31-1-12
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 11/09/2017
Date Tested: 11/08/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 302919
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size 2 in
Bolt Length no data in
Measurement Average 3.34 mils

Test 9 of 11

DIME Test ID: 2017-10-31-1-13
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 11/09/2017
Date Tested: 11/08/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number DDBR
Finish Coating ASTM F2329 - Hot Dip
Product Markings 2H / DH
Size 2 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 26.58
Spacing Ok

Test 10 of 11

DIME Test ID: 2017-10-31-1-14
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 11/09/2017
Date Tested: 11/08/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number W1381
Finish Coating Plain
Product Markings 2H / DH
Size 2 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 28.17
Spacing Ok

Test 11 of 11

DIME Test ID: 2017-10-31-1-15
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 11/09/2017
Date Tested: 11/08/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 302919
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size 2 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 34.8
Spacing Ok

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
2017-10-31-1-3ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)11/08/201711/08/2017Fred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor
2017-10-31-1-4ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)11/08/201711/08/2017Fred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor
2017-10-31-1-5ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)11/08/201711/08/2017Fred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor
2017-10-31-1-6ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)11/08/201711/08/2017Fred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor