Sample Record for 2017-08-10-2
Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project Information
Project ID: 211797 DEA: 080G8424 EFIS: 0814000184
QA Service Level: 1
DIST-CO-RTE-PM: 08-SBD-15-R107.3
Work Description: UPGRADE EXISTING SAFETY ROADSIDE REST AREAS (SRRA)
Location Description: SAN BERNARDINO COUNTY ABOUT 30 MILES EAST OF BARSTOW AT C.V. KANE SAFETY ROADSIDE REST AREA
Contractor Name: HAL HAYS CONSTRUCTION INC.
Contractor Address: 4181 Latham St., Riverside, CA 92501
Resident Engineer: Khoa Nguyen Structure Rep.: Leonard J Romero
Sample Information
DIME Sample ID: 2017-08-10-2
TL Number from the TL Form: Unknown
Sample Submitted By Organization: CT HQ - QASI Los Angeles Field Office
Sample Organization Contact: (858) 285-5797
Type of Sample: Verification
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 08/10/2017
Date that the sample was received by the laboratory/organization performing the testing: 08/21/2017
The quantity of what the sample constitutes: Various
A brief description of the sample: 3/4 inch assorted anchor bolts
From where was the sample collected: Manufacturer
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: California Steel Products
Material Information
Rocap Number(s): N/A
Heat Number(s): 145517
Nut Mfg. Lot Number(s): N/A
Washer Mfg. Lot Number(s): N/A
Bolt Specification: F1554 Gr 36
Bolt Length(s): 7-7/8", 9", 9-1/2", 10"
Nut Specification: N/A
Washer Specification: N/A
Finish: hot-dip galvanized
Diameter/Size: 3/4"
Bolt Mfg. Lot Number: 145517
Rocap Test Requirement(s): No
Lubricant Requirements(s): None
Test Results
Test 1 of 22
DIME Test ID: 2017-08-10-2-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: F1554 Gr 36 Bolt
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments | 1A | F1554 Gr 36 Bolt 10 Deg Wedge | 0.334 | 23605 | 105 | 70674 | 45412 | 15168 | F1554 Gr 36 Bolt |
| |
UTM
|
400KIP
|
Temperature
|
72
|
Test 2 of 22
DIME Test ID: 2017-08-10-2-2
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: F1554 Gr 36 Bolt
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments | 2A | F1554 Gr 36 Bolt 10 Deg Wedge | 0.334 | 23819 | 105 | 71314 | 46901 | 15665 | F1554 Gr 36 Bolt |
| |
UTM
|
400KIP
|
Temperature
|
72
|
Test 3 of 22
DIME Test ID: 2017-08-10-2-3
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
7.875 in
|
Gage Type
|
Pass
|
Test 4 of 22
DIME Test ID: 2017-08-10-2-4
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1B
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
7.875 in
|
Gage Type
|
Pass
|
Test 5 of 22
DIME Test ID: 2017-08-10-2-5
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1C
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
7.875 in
|
Gage Type
|
Pass
|
Test 6 of 22
DIME Test ID: 2017-08-10-2-6
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
2A
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
9 in
|
Gage Type
|
Pass
|
Test 7 of 22
DIME Test ID: 2017-08-10-2-7
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
3A
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
9.5 in
|
Gage Type
|
Pass
|
Test 8 of 22
DIME Test ID: 2017-08-10-2-8
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
3B
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
9.5 in
|
Gage Type
|
Pass
|
Test 9 of 22
DIME Test ID: 2017-08-10-2-9
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
3C
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
9.5 in
|
Gage Type
|
Pass
|
Test 10 of 22
DIME Test ID: 2017-08-10-2-10
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
4A
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
10 in
|
Gage Type
|
Pass
|
Test 11 of 22
DIME Test ID: 2017-08-10-2-11
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
4B
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
10 in
|
Gage Type
|
Pass
|
Test 12 of 22
DIME Test ID: 2017-08-10-2-12
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
4C
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
10 in
|
Gage Type
|
Pass
|
Test 13 of 22
DIME Test ID: 2017-08-10-2-13
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
7.875 in
|
Measurement Average
|
4.27 mils
|
Test 14 of 22
DIME Test ID: 2017-08-10-2-14
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1B
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
7.875 in
|
Measurement Average
|
4.5 mils
|
Test 15 of 22
DIME Test ID: 2017-08-10-2-15
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1C
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
7.875 in
|
Measurement Average
|
5.21 mils
|
Test 16 of 22
DIME Test ID: 2017-08-10-2-16
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
2A
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
9 in
|
Measurement Average
|
5.01 mils
|
Test 17 of 22
DIME Test ID: 2017-08-10-2-17
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
3A
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
9.5 in
|
Measurement Average
|
4.26 mils
|
Test 18 of 22
DIME Test ID: 2017-08-10-2-18
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
3B
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
9.5 in
|
Measurement Average
|
4.81 mils
|
Test 19 of 22
DIME Test ID: 2017-08-10-2-19
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
3C
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
9.5 in
|
Measurement Average
|
4.91 mils
|
Test 20 of 22
DIME Test ID: 2017-08-10-2-20
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
4A
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
10 in
|
Measurement Average
|
4 mils
|
Test 21 of 22
DIME Test ID: 2017-08-10-2-21
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
4B
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
10 in
|
Measurement Average
|
4.07 mils
|
Test 22 of 22
DIME Test ID: 2017-08-10-2-22
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/23/2017
Date Tested: 08/22/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
4C
|
Rocap Number
|
no data
|
Heat Number(s)
|
145517
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
ASTM A153 - Hot Dip
|
Product Markings
|
CSP AB-36 BLUE PAINT
|
Size
|
.75 in
|
Bolt Length
|
10 in
|
Measurement Average
|
3.97 mils
|