Print Report | Back to Sample Detail

Sample Record for 2017-08-10-1

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 211988 DEA: 081C5104 EFIS: 0812000324 QA Service Level: 1
DIST-CO-RTE-PM: 08-RIV-74-17.4/17.8
Work Description: CONSTRUCT VEHICLE RINSE FACILITY
Location Description: RIVERSIDE COUNTY IN AND NEAR LAKE ELSINORE AT THE ELSINORE MAINTENANCE STATION AND FROM DEXTER AVENUE TO CONRAD AVENUE
Contractor Name: HAL HAYS CONSTRUCTION INC.
Contractor Address: 4181 Latham St., Riverside, CA 92501
Resident Engineer: Nick Truong Structure Rep.: Hien Vu

Sample Information

DIME Sample ID: 2017-08-10-1
TL Number from the TL Form: C939702
Sample Submitted By Organization: CT HQ - QASI Los Angeles Field Office
Sample Organization Contact: (858) 285-5797
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 08/10/2017
Date that the sample was received by the laboratory/organization performing the testing: 08/29/2017
The quantity of what the sample constitutes: 40
A brief description of the sample: F1554 Grade 55 HDG Anchor Bolts
From where was the sample collected: Fabricator
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Richardson Steel

Material Information

Rocap Number(s):
Heat Number(s): Bolt 145817 Nut 6214073502 WasherC65743
Nut Mfg. Lot Number(s): 23094-6214073502
Washer Mfg. Lot Number(s): 32537
Bolt Specification: F1554 Gr 36
Bolt Length(s): 19"
Nut Specification: A563
Washer Specification: F436
Finish: HDG
Diameter/Size: 1"
Bolt Mfg. Lot Number:
Rocap Test Requirement(s):
Lubricant Requirements(s):
Test results on following page(s): 8

Test Results

Test 1 of 8

DIME Test ID: 2017-08-10-1-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 08/31/2017
Date Tested: 08/30/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: F1554 Gr 36 Bolt
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleSizeArea (in^2)Peak Load (lbf)Peak Load (kN)Tensile Strength (psi)Stress at Offset (psi)Load at Offset (lbf)Comments
1AF1554 Bolt 10 Deg Wedge0.60644609198736124704128507F1554 Gr 36 Bolt
UTM 400KIP
Temperature 72

Test 2 of 8

DIME Test ID: 2017-08-10-1-2
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 08/31/2017
Date Tested: 08/30/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)CommentsTested By
1AL96-129-171\"93389415.42Nut ProofBrian
UTM 400KIP
Temperature 72 F

Test 3 of 8

DIME Test ID: 2017-08-10-1-3
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 08/31/2017
Date Tested: 08/30/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 145817
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings CSP AB-36 BLUE PAINT
Size 1 in
Bolt Length 19 in
Gage Type Pass

Test 4 of 8

DIME Test ID: 2017-08-10-1-4
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 08/31/2017
Date Tested: 08/30/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 23094-6214073502
Finish Coating ASTM F2329 - Hot Dip
Product Markings U DH
Size 1 in
Gage Type Pass

Test 5 of 8

DIME Test ID: 2017-08-10-1-5
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/31/2017
Date Tested: 08/30/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 145817
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings CSP AB-36 BLUE PAINT
Size 1 in
Bolt Length 19 in
Measurement Average 4.08 mils

Test 6 of 8

DIME Test ID: 2017-08-10-1-6
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/31/2017
Date Tested: 08/30/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 23094-6214073502
Finish Coating ASTM F2329 - Hot Dip
Product Markings U DH
Size 1 in
Bolt Length no data in
Measurement Average 3.34 mils

Test 7 of 8

DIME Test ID: 2017-08-10-1-7
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 08/31/2017
Date Tested: 08/30/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 32537
Finish Coating ASTM F2329 - Hot Dip
Product Markings B
Size 1 in
Bolt Length no data in
Measurement Average 3.45 mils

Test 8 of 8

DIME Test ID: 2017-08-10-1-8
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 08/31/2017
Date Tested: 08/30/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 32537
Finish Coating ASTM F2329 - Hot Dip
Product Markings B
Size 1 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 33.15
Spacing Ok