Print Report | Back to Sample Detail

Sample Record for 2017-07-18-19

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 211948 DEA: 073W2204 EFIS: 0716000011 QA Service Level: 1
DIST-CO-RTE-PM: 07-LA-210-R0.0/R15.8
Work Description: REPLACE BRIDGE APPROACH SLABS AND REHABILITATE DECKS.
Location Description: LOS ANGELES COUNTY IN LOS ANGELES AND GLENDALE FROM NORTH CONNECTOR OVERCROSSING TO HONOLULU AVENUE UNDERCROSSING
Contractor Name: West Coast Structures, Inc.
Contractor Address: 6005 Tyler St., Riverside, CA,92503
Resident Engineer: Patricia Amadi Structure Rep.: Adriana Pimienta

Sample Information

DIME Sample ID: 2017-07-18-19
TL Number from the TL Form: C940652
Sample Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Sample Organization Contact: (916) 227-7253
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 07/18/2017
Date that the sample was received by the laboratory/organization performing the testing: 07/21/2017
The quantity of what the sample constitutes: 1
A brief description of the sample: A307A Threaded Rod
From where was the sample collected: Fabricator
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Ulmer Industries

Material Information

Rocap Number(s):
Heat Number(s): 405414
Nut Mfg. Lot Number(s):
Washer Mfg. Lot Number(s):
Bolt Specification: A307A
Bolt Length(s): 3'-8"
Nut Specification: NA
Washer Specification: NA
Finish: A153 / F2329
Diameter/Size: .750
Bolt Mfg. Lot Number: 1
Rocap Test Requirement(s):
Lubricant Requirements(s):

Test Results

Test 1 of 3

DIME Test ID: 2017-07-18-19-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 07/24/2017
Date Tested: 07/24/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test: A307 A Threaded Stud
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleSizeArea (in^2)Peak Load (lbf)Peak Load (kN)Tensile Strength (psi)Stress at Offset (psi)Load at Offset (lbf)Comments
1AA307 A .750\" x 44\" threaded Rod0.33425620113767076461321581A307 A Threaded Stud
UTM 400KIP
Temperature 72

Test 2 of 3

DIME Test ID: 2017-07-18-19-2
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 07/24/2017
Date Tested: 07/24/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 405414
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A307 A
Size .750 in
Bolt Length 44 in
Gage Type Pass

Test 3 of 3

DIME Test ID: 2017-07-18-19-3
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 07/24/2017
Date Tested: 07/24/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Blvd,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: paul.lukkarila@dot.ca.gov
Organization Phone: (916) 227-7253
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 405414
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A307 A
Size .750 in
Bolt Length 44 in
Measurement Average 5.31 mils

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
No tests have been assigned to this sample.