Print Report | Back to Sample Detail

Sample Record for 2017-04-24-2

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 211223 DEA: 010B27U4 EFIS: 0115000111 QA Service Level: 1
DIST-CO-RTE-PM: 01-DN-101-14.9/15.3
Work Description: CONSTRUCT RETAINING WALLS AND RECONSTRUCT ROADWAY
Location Description: DEL NORTE COUNTY ABOUT 10 MILES NORTH OF KLAMATH FROM 2.2 MILES TO 2.6 MILES NORTH OF WILSON CREEK BRIDGE
Contractor Name: STEWART ENGINEERING INC
Contractor Address: P.O. Box 990010, Redding, CA 96099-0010
Resident Engineer: Karen Sanders Structure Rep.: Brian Cinkutis

Sample Information

DIME Sample ID: 2017-04-24-2
TL Number from the TL Form: C944451
Sample Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Sample Organization Contact: (530) 329-6527
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 04/24/2017
Date that the sample was received by the laboratory/organization performing the testing: 05/11/2017
The quantity of what the sample constitutes: 12
A brief description of the sample: F1554 Grade 105 HDG Anchor Bolts
From where was the sample collected: Job Site
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Gaffney Bolt Compant

Material Information

Rocap Number(s):
Heat Number(s): 62140458-03
Nut Mfg. Lot Number(s): 308034A
Washer Mfg. Lot Number(s): 0812-881
Bolt Specification: F1554-105 HDG
Bolt Length(s): 24"
Nut Specification: A563
Washer Specification: F436
Finish: HDG
Diameter/Size: 0.875
Bolt Mfg. Lot Number:
Rocap Test Requirement(s):
Lubricant Requirements(s):

Test Results

Test 1 of 19

DIME Test ID: 2017-04-24-2-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 05/15/2017
Date Tested: 05/01/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: F1554 G105
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleSizeArea (in^2)Peak Load (lbf)Peak Load (kN)Tensile Strength (psi)Stress at Offset (psi)Load at Offset (lbf)Comments
1AA449 7/8\" x 24\' Bolt 10 Deg Wedge0.4625891726212752611769754376F1554 G105
UTM 400KIP
Temperature 71

Test 2 of 19

DIME Test ID: 2017-04-24-2-2
Test Method: ASME B1.2-83r01: (Pitch Diameter) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Pitch Diameter)
Verified Date: 05/15/2017
Date Tested: 05/02/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 62140458-03
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings RED PAINT
Size 0.875 in
Bolt Length 24 in
Pitch Diameter 0.8035 in
Pitch Diameter 2nd no data in

Test 3 of 19

DIME Test ID: 2017-04-24-2-3
Test Method: ASME B1.2-83r01: (Pitch Diameter) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Pitch Diameter)
Verified Date: 05/15/2017
Date Tested: 05/02/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) 62140458-03
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings RED PAINT
Size 0.875 in
Bolt Length 24 in
Pitch Diameter 0.8029 in
Pitch Diameter 2nd no data in

Test 4 of 19

DIME Test ID: 2017-04-24-2-4
Test Method: ASME B1.2-83r01: (Pitch Diameter) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Pitch Diameter)
Verified Date: 05/15/2017
Date Tested: 05/02/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) 62140458-03
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings RED PAINT
Size 0.875 in
Bolt Length 24 in
Pitch Diameter 0.8050 in
Pitch Diameter 2nd no data in

Test 5 of 19

DIME Test ID: 2017-04-24-2-5
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/15/2017
Date Tested: 05/02/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 62140458-03
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings RED PAINT
Size 0.875 in
Bolt Length 24 in
Measurement Average 3.19 mils

Test 6 of 19

DIME Test ID: 2017-04-24-2-6
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/15/2017
Date Tested: 05/02/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) 62140458-03
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings RED PAINT
Size 0.875 in
Bolt Length 24 in
Measurement Average 3.4 mils

Test 7 of 19

DIME Test ID: 2017-04-24-2-7
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/15/2017
Date Tested: 05/02/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) 62140458-03
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings RED PAINT
Size 0.875 in
Bolt Length 24 in
Measurement Average 3.66 mils

Test 8 of 19

DIME Test ID: 2017-04-24-2-8
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof Load
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)CommentsTested By
1AN/A7/8\"70491313.56Nut Proof LoadArnold
UTM 400KIP
Temperature 71 F

Test 9 of 19

DIME Test ID: 2017-04-24-2-9
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 308034A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size no data in
Gage Type Pass

Test 10 of 19

DIME Test ID: 2017-04-24-2-10
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 308034A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size no data in
Gage Type Pass

Test 11 of 19

DIME Test ID: 2017-04-24-2-11
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 308034A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size no data in
Gage Type Pass

Test 12 of 19

DIME Test ID: 2017-04-24-2-12
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 308034A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size no data in
Bolt Length no data in
Measurement Average 2.25 mils

Test 13 of 19

DIME Test ID: 2017-04-24-2-13
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 308034A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size no data in
Bolt Length no data in
Measurement Average 4.07 mils

Test 14 of 19

DIME Test ID: 2017-04-24-2-14
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 308034A
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH N
Size no data in
Bolt Length no data in
Measurement Average 3.06 mils

Test 15 of 19

DIME Test ID: 2017-04-24-2-15
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 298421
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size no data in
Bolt Length no data in
Measurement Average 2.05 mils

Test 16 of 19

DIME Test ID: 2017-04-24-2-16
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 298421
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size no data in
Bolt Length no data in
Measurement Average 2.66 mils

Test 17 of 19

DIME Test ID: 2017-04-24-2-17
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 298421
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size no data in
Bolt Length no data in
Measurement Average 2.84 mils

Test 18 of 19

DIME Test ID: 2017-04-24-2-18
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 298421
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size no data in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 35.7
Spacing Ok

Test 19 of 19

DIME Test ID: 2017-04-24-2-19
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 05/15/2017
Date Tested: 05/15/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 298421
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size no data in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 36.3
Spacing Ok