Print Report | Back to Sample Detail

Sample Record for 2017-04-01-4

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 210695 DEA: 080K2924 EFIS: 0812000099 QA Service Level: 1
DIST-CO-RTE-PM: 08-SBD-10-32.9/R37.4
Work Description: REPLACE EXISTING (PCCP) WITH (RSCP).
Location Description: IN/NEAR REDLANDS FROM 0.2 MILE W/O FORD STREET TO 0.4 MILE E/O LIVEOAK CANYON ROAD.
Contractor Name: J. MCLOUGHLIN ENGINEERING CO., INC.
Contractor Address: 10641 Fulton Court, Rancho Cucamonga, CA 91730
Resident Engineer: Maged Youssef Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2017-04-01-4
TL Number from the TL Form: 20-4
Sample Submitted By Organization: CT D08 - Fontana Southern Regional Laboratory
Sample Organization Contact: 213-792-4794
Type of Sample: Quality Control
Type of Material: Concrete
Sample Taken Date: 04/01/2017
Date that the sample was received by the laboratory/organization performing the testing: 04/03/2017
The quantity of what the sample constitutes: 6
A brief description of the sample: 6x12 LCB
From where was the sample collected: Job Site
Laboratory sample identification: 945-20-4
Structure unique identifier: 10WB STA 733 10 to 697 00
Structure name: Unknown
The fabricator/manufacturer/facility name: CTS SHORT LOAD RAPID SET

Material Information

The concrete mix design number: CTS-30-RAM
The truck number from where the sample was collected: Unknown
The batch plant ticket number from where the sample was collected: NA
Concrete batch plant: Unknown
The fabricator/manufacturer designation for the sample: Unknown
A detailed description of where the material sample was collected: NP
Where the material sample would have been placed if not sampled: Unknown
From Lot No.: Unknown
Bag Lot No.: Unknown
Test results on following page(s): 1

Test Results

Test 1 of 1

DIME Test ID: 2017-04-01-4-1
Test Method: ASTM C39-17a: Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens
Verified Date: 04/11/2017
Date Tested: 04/08/2017
Submitted By Organization: CT D08 - Fontana Southern Regional Laboratory
Organization Address: 13970 Victoria Street,
Organization City: Fontana
Organization State: CA
Organization Zipcode: 92336
Organization Email: jose.guzman@dot.ca.gov
Organization Phone: 9098293029
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Unit system used? US Units
Number of specimens 6
Test performed With no density determined
Capped in accordance with? ASTM C617/CTM521
Average diameter of cylinder 1 6.01 in
Average diameter of cylinder 2 6.02 in
Average diameter of cylinder 3 6.02 in
Average diameter of cylinder 4 6.02 in
Average diameter of cylinder 5 6.02 in
Average diameter of cylinder 6 6.02 in
Cross sectional area of cylinder 1 28.37 in^2
Cross sectional area of cylinder 2 28.46 in^2
Cross sectional area of cylinder 3 28.46 in^2
Cross sectional area of cylinder 4 28.46 in^2
Cross sectional area of cylinder 5 28.46 in^2
Cross sectional area of cylinder 6 28.46 in^2
Compressive strength (to nearest 10 psi) 6460 psi
Maximum load on cylinder 1 70360 lb
Maximum load on cylinder 2 72190 lb
Maximum load on cylinder 3 70060 lb
Maximum load on cylinder 4 70900 lb
Maximum load on cylinder 5 71810 lb
Maximum load on cylinder 6 747202 lb
Compressive strength of cylinder 1 2480.1 psi
Type of fracture pattern of cylinder 1 1
Compressive strength of cylinder 2 2536.5 psi
Compressive strength of cylinder 3 2461.7 psi
Compressive strength of cylinder 4 2491.2 psi
Compressive strength of cylinder 5 2523.2 psi
Compressive strength of cylinder 6 26254.5 psi
Type of fracture pattern of cylinder 2 1
Type of fracture pattern of cylinder 3 1
Type of fracture pattern of cylinder 4 1
Type of fracture pattern of cylinder 5 1
Type of fracture pattern of cylinder 6 1
Comment on any defect in either specimen or caps (Max 250 Characters) no data
Correction factor for cylinder 1 1
Correction factor for cylinder 2 no data
Correction factor for cylinder 3 no data
Correction factor for cylinder 4 no data
Correction factor for cylinder 5 no data
Correction factor for cylinder 6 no data
Age of specimen 7 days
Age of specimen in hours no data