Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project ID: 209820 DEA: 04297634 EFIS: 0415000040 COOP: 042548
QA Service Level: 1
DIST-CO-RTE-PM: 04-ALA-84,680-17.9/21
Work Description: ROUTE 84 WIDENING (4-LANE EXPRESSWAY) FROM I-680 TO PIGEON PASS, INCLUDING INTERSECTION, DRAINAGE IMPROVEMENTS AND UTILITY RELOCATION.
Location Description: ALAMEDA COUNTY IN AND NEAR SUNOL, PLEASANTON, AND LIVERMORE ON ROUTE 84 FROM 0.1 MILE EAST OF ROUTE 680 TO 0.1 MILE SOUTH OF RUBY HILL DRIVE AND ON ROUTE 680 FROM 1.2 MILES SOUTH TO 1.8 MILES NORTH OF ROUTE 84
Contractor Name: Bay Cities Paving & Grading
Contractor Address: 1450 Civic Ct. BLDG B #400, Concord CA, 94520
Resident Engineer: Paramjit Pandher Structure Rep.: Kristen We
DIME Sample ID: 2024-09-26-46
TL Number from the TL Form: C031272
Sample Submitted By Organization: CT D04 - Pleasanton Field Laboratory
Sample Organization Contact: (510) 224-6127
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 09/26/2024
Date that the sample was received by the laboratory/organization performing the testing: 09/27/2024
The quantity of what the sample constitutes: 750 Tons
A brief description of the sample: 3/4 HMA-SP Type A
From where was the sample collected: Source
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Vulcan Pleasanton
DIME Test ID: 2024-09-26-46-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 09/30/2024
Date Tested: 09/28/2024
Submitted By Organization: CT D04 - Pleasanton Field Laboratory
Organization Address: 5675 B Gibratar Drive,
Organization City: Pleasanton
Organization State: CA
Organization Zipcode: 94588
Organization Email: dennis.yeung@dot.ca.gov
Organization Phone: (510) 224-6127
General Comments for this Test: Lot 15 Sublot 10
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used?
|
Celsius
|
Test procedure used?
|
Method A
|
Mass of the specimen basket assembly
|
2910.3 g
|
Mass of the specimen and specimen basket assembly prior to ignition
|
4965.7 g
|
Mass of HMA Sample prior to ignition
|
2055.4 g
|
Corrected Asphalt Binder Content
|
5.02 %
|
Mass Loss
|
130.8 g
|
Mass of aggregate remaining after ignition
|
1924.6 g
|
Correction Factor (Percent by mass of HMA Specimen)
|
1.19 %
|
Moisture Content
|
no data0 %
|
Temperature Compensation Factor
|
0.15 %
|
Test Temperature
|
482 C
|
DIME Test ID: 2024-09-26-46-2
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 09/30/2024
Date Tested: 09/28/2024
Submitted By Organization: CT D04 - Pleasanton Field Laboratory
Organization Address: 5675 B Gibratar Drive,
Organization City: Pleasanton
Organization State: CA
Organization Zipcode: 94588
Organization Email: dennis.yeung@dot.ca.gov
Organization Phone: (510) 224-6127
General Comments for this Test: Lot 15 Sublot 10
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of Samples
|
1
|
What is the unit of measurement for theoretical density?
|
SI Units
|
Mass Determination
|
Air
|
Method Performed
|
Mechanical Agitation - Method A
|
Mass of container filled with water 1
|
7335.6 grams
|
Mass of oven-dry sample in air for Sample 1
|
2536.8 grams
|
Mass of container filled with the sample and water for Sample 1
|
8860.8 grams
|
Temperature of Water
|
77 °F
|
Specific Gravity for Sample 1
|
2.508
|
Theoretical maximum density at 25°C (77°F)
|
2501 kg/m^3
|
DIME Test ID: 2024-09-26-46-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 09/30/2024
Date Tested: 09/28/2024
Submitted By Organization: CT D04 - Pleasanton Field Laboratory
Organization Address: 5675 B Gibratar Drive,
Organization City: Pleasanton
Organization State: CA
Organization Zipcode: 94588
Organization Email: dennis.yeung@dot.ca.gov
Organization Phone: (510) 224-6127
General Comments for this Test: Lot 15 Sublot 10
Test Result Compliance: not applicable
Additional Comments When Verified:
Bulk Specific Gravity
|
2.4
|
Bulk Specific Gravity 2
|
2.377
|
Bulk Specific Gravity 3
|
2.421
|
Average Bulk Specific Gravity
|
2.399
|
DIME Test ID: 2024-09-26-46-4
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 09/30/2024
Date Tested: 09/28/2024
Submitted By Organization: CT D04 - Pleasanton Field Laboratory
Organization Address: 5675 B Gibratar Drive,
Organization City: Pleasanton
Organization State: CA
Organization Zipcode: 94588
Organization Email: dennis.yeung@dot.ca.gov
Organization Phone: (510) 224-6127
General Comments for this Test: Lot 15 Sublot 10
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids
|
4.3 %
|
Percent Air Voids 2
|
5.2 %
|
Percent Air Voids 3
|
3.5 %
|
Average Percent Air Voids
|
4.3 %
|
DIME Test ID: 2024-09-26-46-5
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 09/30/2024
Date Tested: 09/28/2024
Submitted By Organization: CT D04 - Pleasanton Field Laboratory
Organization Address: 5675 B Gibratar Drive,
Organization City: Pleasanton
Organization State: CA
Organization Zipcode: 94588
Organization Email: dennis.yeung@dot.ca.gov
Organization Phone: (510) 224-6127
General Comments for this Test: Lot 15 Sublot 11
Test Result Compliance: not applicable
Additional Comments When Verified:
Bulk Specific Gravity
|
2.396
|
Bulk Specific Gravity 2
|
2.355
|
Bulk Specific Gravity 3
|
2.351
|
Average Bulk Specific Gravity
|
2.367
|
DIME Test ID: 2024-09-26-46-6
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 09/30/2024
Date Tested: 09/28/2024
Submitted By Organization: CT D04 - Pleasanton Field Laboratory
Organization Address: 5675 B Gibratar Drive,
Organization City: Pleasanton
Organization State: CA
Organization Zipcode: 94588
Organization Email: dennis.yeung@dot.ca.gov
Organization Phone: (510) 224-6127
General Comments for this Test: Lot 15 Sublot 11
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids
|
4.5 %
|
Percent Air Voids 2
|
6.1 %
|
Percent Air Voids 3
|
6.3 %
|
Average Percent Air Voids
|
5.6 %
|
DIME Test ID: 2024-09-26-46-7
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 09/30/2024
Date Tested: 09/28/2024
Submitted By Organization: CT D04 - Pleasanton Field Laboratory
Organization Address: 5675 B Gibratar Drive,
Organization City: Pleasanton
Organization State: CA
Organization Zipcode: 94588
Organization Email: dennis.yeung@dot.ca.gov
Organization Phone: (510) 224-6127
General Comments for this Test: Lot 15 Sublot 12
Test Result Compliance: not applicable
Additional Comments When Verified:
Bulk Specific Gravity
|
2.355
|
DIME Test ID: 2024-09-26-46-8
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 09/30/2024
Date Tested: 09/28/2024
Submitted By Organization: CT D04 - Pleasanton Field Laboratory
Organization Address: 5675 B Gibratar Drive,
Organization City: Pleasanton
Organization State: CA
Organization Zipcode: 94588
Organization Email: dennis.yeung@dot.ca.gov
Organization Phone: (510) 224-6127
General Comments for this Test: Lot 15 Sublot 12
Test Result Compliance: complies
Additional Comments When Verified:
DIME Test ID: 2024-09-26-46-9
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 11/27/2024
Date Tested: 11/22/2024
Submitted By Organization: CT D04 - Pleasanton Field Laboratory
Organization Address: 5675 B Gibratar Drive,
Organization City: Pleasanton
Organization State: CA
Organization Zipcode: 94588
Organization Email: dennis.yeung@dot.ca.gov
Organization Phone: (510) 224-6127
General Comments for this Test: Lot 15 Sublot 11
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used?
|
Celsius
|
Test procedure used?
|
Method A
|
Mass of the specimen basket assembly
|
2907.2 g
|
Mass of the specimen and specimen basket assembly prior to ignition
|
4952.2 g
|
Mass of HMA Sample prior to ignition
|
2045 g
|
Corrected Asphalt Binder Content
|
4.4 %
|
Mass Loss
|
117.4 g
|
Mass of aggregate remaining after ignition
|
1927.6 g
|
Correction Factor (Percent by mass of HMA Specimen)
|
1.19 %
|
Moisture Content
|
no data0 %
|
Temperature Compensation Factor
|
0.15 %
|
Test Temperature
|
482 C
|
DIME Test ID: 2024-09-26-46-10
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 11/27/2024
Date Tested: 11/22/2024
Submitted By Organization: CT D04 - Pleasanton Field Laboratory
Organization Address: 5675 B Gibratar Drive,
Organization City: Pleasanton
Organization State: CA
Organization Zipcode: 94588
Organization Email: dennis.yeung@dot.ca.gov
Organization Phone: (510) 224-6127
General Comments for this Test: Lot 15 Sublot 12
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used?
|
Celsius
|
Test procedure used?
|
Method A
|
Mass of the specimen basket assembly
|
2872.1 g
|
Mass of the specimen and specimen basket assembly prior to ignition
|
4922 g
|
Mass of HMA Sample prior to ignition
|
2049.9 g
|
Corrected Asphalt Binder Content
|
4.75 %
|
Mass Loss
|
124.8 g
|
Mass of aggregate remaining after ignition
|
1925.1 g
|
Correction Factor (Percent by mass of HMA Specimen)
|
1.19 %
|
Moisture Content
|
no data0 %
|
Temperature Compensation Factor
|
0.15 %
|
Test Temperature
|
482 C
|