Print Report | Back to Sample Detail

Sample Record for 2024-09-09-76

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 994696 DEA: 100Y7704 EFIS: 1015000008 QA Service Level: 1
DIST-CO-RTE-PM: 10-MPA-140-12.0/22.1
Work Description: REPLACE AC SURFACING, PLACE HMA AND RHMA, AND BRIDGE REPAIR.
Location Description: MARIPOSA COUNTY NEAR MARIPOSA FROM 1.3 MILES EAST OF CATHEYS VALLEY PARK TO 0.1 MILE NORTH OF ROUTE 49
Contractor Name: GEORGE REED, INC.
Contractor Address: 140 EMPIRE AVE, MODESTO CA 95354
Resident Engineer: Troy Scheiber Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2024-09-09-76
TL Number from the TL Form: 0Y77116
Sample Submitted By Organization: CT D10 - District 10 Materials Laboratory
Sample Organization Contact: (209) 948-7567
Type of Sample: Quality Assurance
Type of Material: Hot Mix Asphalt
Sample Taken Date: 09/09/2024
Date that the sample was received by the laboratory/organization performing the testing: 09/13/2024
The quantity of what the sample constitutes: 4 boxes
A brief description of the sample: 3/4 HMA
From where was the sample collected: Manufacturer
Laboratory sample identification: 24-H-117
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: George Reed - Table Mountain Plant

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number: 1
Sublot number: 16
HMA Mix Number: 24J003

Test Results

Test 1 of 2

DIME Test ID: 2024-09-09-76-1
Test Method: AASHTO T209-22: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 09/19/2024
Date Tested: 09/17/2024
Submitted By Organization: CT D10 - District 10 Materials Laboratory
Organization Address: 1976 East Dr. Martin Luther King Jr. Boulevard,
Organization City: Stockton
Organization State: CA
Organization Zipcode: 95205
Organization Email: mandeep.dhesi@dot.ca.gov
Organization Phone: (209) 948-7567
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of Samples 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Water
Specific Gravity for Sample 1 2.464
Theoretical maximum density at 25°C (77°F) 153.3 lb/ft^3

Test 2 of 2

DIME Test ID: 2024-09-09-76-2
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 09/19/2024
Date Tested: 09/17/2024
Submitted By Organization: CT D10 - District 10 Materials Laboratory
Organization Address: 1976 East Dr. Martin Luther King Jr. Boulevard,
Organization City: Stockton
Organization State: CA
Organization Zipcode: 95205
Organization Email: mandeep.dhesi@dot.ca.gov
Organization Phone: (209) 948-7567
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used? Celsius
Test procedure used? Method A
Mass of HMA Sample prior to ignition 2040 g
Corrected Asphalt Binder Content 5.28 %
Mass Loss 118.8 g
Correction Factor (Percent by mass of HMA Specimen) 0.4 %
Moisture Content no data0 %
Temperature Compensation Factor 0.15 %
Test Temperature 538 C