Print Report | Back to Sample Detail

Sample Record for 2024-07-21-13

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 995055 DEA: 024H0504 EFIS: 0218000080 QA Service Level: 1
DIST-CO-RTE-PM: 02-SHA-273,299-18.5/18.7,24.1/30.3
Work Description: PLACE RHMA, HMA, MINOR CONCRETE, AND REPLACE AC SURFACING.
Location Description: SHASTA COUNTY IN AND NEAR REDDING ON ROUTE 273 FROM 0.5 MILE NORTH OF SULPHUR CREEK BRIDGE TO 0.2 MILE SOUTH OF TWIN VIEW BOULEVARD AND ON ROUTE 299 FROM 0.2 MILE WEST OF HILLTOP DRIVE TO 0.1 MILE EAST OF HOOTENANNY LANE
Contractor Name: TULLIS, INC.
Contractor Address: 16951 Clear Creek Road, Redding, CA 96001
Resident Engineer: Nathan Alexander Structure Rep.: Nicolas Jimenez

Sample Information

DIME Sample ID: 2024-07-21-13
TL Number from the TL Form: 858503
Sample Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Sample Organization Contact: (916) 227-7302
Type of Sample: Production Start-Up
Type of Material: Asphalt Rubber Binder
Sample Taken Date: 07/21/2024
Date that the sample was received by the laboratory/organization performing the testing: 07/24/2024
The quantity of what the sample constitutes: 2 CANS
A brief description of the sample: PSU
From where was the sample collected: Source
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: VELERO BENCIA

Material Information

Asphalt modifier supplier: Valero Benicia
Performance Grade: PG 64-16
Lot number:
Sublot number:
Asphalt Rubber Binder Mix Number:
Test results on following page(s): 4

Test Results

Test 1 of 4

DIME Test ID: 2024-07-21-13-1
Test Method: ASTM D217-16: Standard Test Methods for Cone Penetration of Lubricating Grease (Cone Penetration)
Verified Date: 07/26/2024
Date Tested: 07/25/2024
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (530) 713-6823
General Comments for this Test: CONE PENETRATION
Test Result Compliance: complies
Additional Comments When Verified:
Determination Unworked Penetration
Unworked Penetration 29 0.1 mm

Test 2 of 4

DIME Test ID: 2024-07-21-13-2
Test Method: ASTM D36-14ε1: Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) (Softening Point)
Verified Date: 07/26/2024
Date Tested: 07/25/2024
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (530) 713-6823
General Comments for this Test: SOFTENING POINT
Test Result Compliance: does not comply
Additional Comments When Verified:
ASTM Thermometer used? C
Softening Point Sample 1 78 C
Softening Point Sample 2 77 C
Bath Liquid freshly boiled distilled water
Minutes Reaction no data

Test 3 of 4

DIME Test ID: 2024-07-21-13-3
Test Method: ASTM D5329-16: Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements (Asphalt Pavement)
Verified Date: 07/26/2024
Date Tested: 07/25/2024
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (530) 713-6823
General Comments for this Test: RESILIENCE
Test Result Compliance: complies
Additional Comments When Verified:
Temperature 25 C
Ball Penetration (P1) no data0 mm
Final Dial reading (F1) 60 mm
Ball Penetration (P2) no data0 mm
Final Dial reading (F2) 60 mm
Ball Penetration (P3) no data0 mm
Final Dial reading (F3) 59 mm
Resilience 1 40 %
Resilience 2 40 %
Resilience 3 41 %
Average Resilience 40 %
Minutes Reaction no data

Test 4 of 4

DIME Test ID: 2024-07-21-13-4
Test Method: ASTM D36-14ε1: Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) (Softening Point)
Verified Date: 07/26/2024
Date Tested: 07/26/2024
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (530) 713-6823
General Comments for this Test: RETEST of Softening Point
Test Result Compliance: does not comply
Additional Comments When Verified:
ASTM Thermometer used? C
Softening Point Sample 1 76 C
Softening Point Sample 2 77 C
Bath Liquid freshly boiled distilled water
Minutes Reaction no data